• REM_0000298913_Color_Flex_Fill_ML.tif

    Article No. 298913

    Color Flex Fill

    Highly elastic primer with good filling properties

    antique white (intrinsic colour) | 2989
    Size / Quantity

    Note: This container size is being phased out and is only available to a limited extent.

    Brochures and Catalogues


    Product specifications

    Binder base UV-crosslinking hybrid acrylate copolymer
    Density (20°C) 1.2 g/cm³
    pH value > 8.5
    Pigmentation TiO2
    Extender Mineral filler

    Once fully cured

    Alkali resistance Up to pH 14
    Degree of gloss Matt
    Surface structure Dependent on application method

    The stated values represent typical product characteristics and are not to be construed as binding product specifications.

    Field of application

    • For use outdoors
    • Facades and concrete surfaces
    • Load-bearing, adhering old coatings on a mineral or synthetic resin base
    • Cement-bound, mineral renders (DIN V 18550) P II and P III with a compressive strength > 7 N/mm2
    • Cracked facade surfaces
    • Surface reinforcement in combination with Kobau Arkoflex® Gewirke Typ 150


    • High crack-bridging capability
    • High filling power
    • Preparation
      • Substrate requirements

        The substrate must be dry, clean, load-bearing and free of dust.

        Free of aggressive salts.

      • Preparations

        Prime load-bearing, mineral substrates with Funcosil BI.

    • Application
      • Application temperature: min. 5 °C max. 30 °C
      • Application
      • Application requirements

        Temperature of the material, air and substrate: from min. +5 °C to max. +30 °C

      • Stir well.

        Coat the surface using a suitable tool.

        Apply the material in 2 or 3 coats, depending on the condition of the substrate.

        Wait at least 24 hours before applying subsequent layers.

        Alternatively, embed a textile material (Kobau Arkoflex® Gewirke Typ 150) into the first layer for surface reinforcement.


        Smooth surface

        Apply material using a lamb's wool roller.

        Use a brush to work the material into the gaps, making sure that the material does not accumulate in any spots.


        Textured surface

        Apply the material evenly using a lamb's wool roller. Then, use an appropriate textured roller to achieve the desired texture.

    • Working tools / cleaning
      • Application
      • Roller, brush, surface brush and stainless steel trowel

      • Clean tools, equipment and any splashed material immediately with water while still fresh.

    • Storage / shelf life
      • Store frost-free and cool / protect for moisture / close containers
      • Shelf-life 12 months
      • If stored unopened in its original container in a cool, dry place and protected against frost, the product will keep for at least 12 months.

    • Usage
      • Total application/absorption rate 300 ml - 1000 ml Total / m²
      • Approx. 0.30 - 1.00 l/m² depending on the unevenness of the substrate.

      • Apply to a large enough trial area to determine the precise amount required.

    • General information
      • Current regulations and legal requirements must be taken into account and deviations from these must be agreed separately.

        The relevant test certificates must be observed when planning and carrying out work.

        Primarily lime-based substrates are not suitable for coating.

    • Disposal instructions
      • Larger quantities of leftover product should be disposed of in the original containers in accordance with the applicable regulations. Completely empty, clean containers should be recycled. Do not dispose of together with household waste. Do not allow to enter the sewage system. Do not empty into drains.

    • Safety / regulations
      • For further information on the safety aspects of transporting, storing and handling the product and on disposal and environmental matters, please see the current Safety Data Sheet.

    Possible system products

    Tools, accessories and PPE