Article No. 770101

HSO-118 High Solid Oil [eco]

High-solid wood finish made from renewable raw materials

Colour: intense white (RC-995) | 7701
Colour: intense white (RC-995) | 7701
Please choose a colour
Size / Quantity

Product specifications

On delivery

Binder Modified oils based on renewable raw materials
Density (20°C) Approx. 0.96 g/cm³
Odour Mild
Degree of gloss Matt
Viscosity Approx. 170 mPas

The stated values represent typical product characteristics and are not to be construed as binding product specifications.

Field of application

  • For use indoors
  • for stairs
  • for wood floors
  • for furniture
  • For professional users only
  • Interior wood
  • Wooden floors and stairs
  • Tables and worktops
  • High-quality solid wood furniture
  • Cork floors
  • Panels and moulding
  • Reducing the tendency of natural stone kitchen worktops to accumulate contamination (oil, grease, household dirt, etc.)
  • Sustainable building suitable for building certifications DGnB, LEED, BNB

Properties

  • 3 in 1 oil: stain, oil and wax sealant
  • Made from at least 90% renewable raw materials
  • Food safe: harmless upon contact with food
  • Complies with the principles for the health assessment of construction products used indoors (AgBB scheme)
  • Slip-resistant
  • Easy to apply
  • Penetrates deeply into the wood and emphasises the grain
  • Long-lasting, dirt-repelling and hard-wearing
  • Good resistance against selected standard household substances in accordance with DIN 68861, 1B (e. g. water, cola, beer, tea, coffee, wine & cleaning agents)
  • A vegan product based on the information available to us
  • Preparation
    • Substrate requirements

      The substrate must be clean, dry, free of dust, grease and loose substances, and prepared in the correct manner.

      Wood moisture content: 8-12%

    • Preparations

      Thoroughly remove any dirt, grease and non-adhering old coatings.

      Wash off greasy or resin-rich woods/substrates with WV-891 or V-890.

      Sand wood with P 80 - 150.

      The coarser the sanded finish, the more intense the colouring in pigmented varieties will be.

  • Application
    • Application temperature: min. 18 °C max. 25 °C
    • Stir before use
    • By brush / By roller / Filling knife
    • Stir well.

      Application by roller, brush, spreader or pad.

      Smooth over to ensure that the product is distributed evenly on wood with different levels of absorbency.

      When applying each coat, remove any excess oil using a lint-free cotton cloth after approximately 20-30 minutes.

      On larger surfaces, a single disc machine with a white polishing pad can be used.

      Use cotton rags/cloths on items of furniture.

      Inside cupboards and drawers, only apply a single thin layer of the product using a lint-free cotton cloth.

      Depending on the conditions of the substrate, apply 1 or 2 coats.

      Carry out intermediate sanding with P 240 - 320 before applying a second coat.

  • Application instructions
    • Drying time: can be worked over after 12 - 16 h
    • Check colour, adhesion and compatibility with the substrate by setting up a trial area.

      Before coating technically modified woods and wood-based materials, apply the coating to a trial surface and conduct a suitability test on the desired area of use.

      In the unlikely event that the wood condition or species means that a second coat is required, a drying time of approx. 2-3 days from the second application must be calculated until the coating can sustain foot traffic.

      Only use on absorbent woods and substrates. Not suitable for surfaces that have already been varnished or sealed.

      Ensure thorough ventilation during processing and drying.

      Risk of self-ignition (DGUV information brochure 209-046).

      The product should not be applied at the same work stand as NC-based varnishes or stains. Collect any textiles soiled with the product (e.g. cleaning rags, work clothing) in fire-resistant waste containers and dispose of properly.

    • Drying

      Can be overcoated: after drying overnight Gentle use (e.g. water loads): after 2 -3 days Full loading capacity: after 7 days Recommended drying time before sealing with MultiSil: > 7 days (Remove any smoothing agent residues immediately)

      Practice values at +20 °C and 65% relative humidity.

      Drying is dependent on the type of wood and the absorbency of the substrate.

      Excess material on non-absorbent areas may delay drying, as will low temperatures, poor ventilation and high humidity.

    • Thinning

      Ready to use

  • Working tools / cleaning
    • By brush / By roller / Filling knife
    • Flat brush, short-pile (3-5 mm) velour or mohair roller, rotary disc machine with white non-abrasive pad, wadded rag/lint-free cotton cloth, stainless steel/spring spatula

    • Clean tools using WV-891 Brush Wash or V-890 Thinner.

      Ensure that any residue from cleaning is disposed of correctly.

  • Storage / shelf life
    • Store frost-free and cool / protect for moisture / close containers
    • Shelf-life 24 months
    • If stored unopened in its original container in a cool, dry place and protected against frost, the product will keep for at least 24 months.

  • Usage
    • Approx. 50 ml - 70 ml / m² per layer applied
    • 50 - 70 ml/m² per coat The application rate depends heavily on the absorbency of the wood and the final sanded finish. For every coat, remove excess material after approx. 20-30 minutes using a lint-free cotton cloth.

  • General information
    • In the event of maintenance, treat the cleaned surface in such a way that it blends in to produce a uniform finish.

      Remove water marks or stains on furniture with steel wool (grade 000) and apply a thin layer of the product.

      Observe the "Care instructions for oiled surfaces and floors".

  • Disposal instructions
    • Larger quantities of leftover product should be disposed of in the original containers in accordance with the applicable regulations. Completely empty, clean containers should be recycled. Do not dispose of together with household waste. Do not allow to enter the sewage system. Do not empty into drains.

  • Safety / regulations
    • For further information on the safety aspects of transporting, storing and handling the product and on disposal and environmental matters, please see the current Safety Data Sheet.

Possible system products