Article No. 531005

    Aqua SL-418 Finish

    Transparent, single-component finish with high durability

    Button EN 71/3 Schaukelpferd Button remmers-mix

    Product specifications

    On delivery

    Binder Acrylate dispersion
    Density (20°C) Approx. 1.05 g/cm³
    Odour Characteristic
    Runout time s in DIN 6 cup Approx. 30

    The stated values represent typical product characteristics and are not to be construed as binding product specifications.

    Field of application

    • For use indoors
    • for interior doors
    • for furniture
    • For professional users only
    • Interior wood
    • Primer & top coat
    • Solid wood & veneers
    • Living room & bedroom furniture
    • Interior finishing work: e.g. panels, borders, cladding & interior doors
    • Shop fitting and trade fair stands
    • As a glass lacquer (in combination with Aqua VGA-485)

    Properties

    • Water-based
    • Water-based lacquer that can be sprayed to give an even layer (no milky wet film)
    • Can also be used on vertical surfaces
    • Good sanding properties
    • Good block resistance
    • Good flow properties
    • Elegant pore pattern
    • Resistant to chemicals: DIN 68861, 1B
    • Good resistance to a wide range of commercially available hand creams
    • Excellent emphasis of the grain
    • Lightfast
    • Surfaces show no tendency to become glossy
    • Pleasant feel
    • Preparation
      • Substrate requirements

        The substrate must be clean, dry, free of dust, grease and loose substances, and prepared in the correct manner.

        Wood moisture content: 8-12%

      • Preparations

        Wash off greasy or resin-rich woods/substrates with WV-891 or V-890.

        Clean glass using V-890 or UN-894.

        Sand wood using P 100 - 180 grit.

        Sand panels using P 180 - 320 grit.

        Sand lacquer using P 240 - 320 grit.

        If colouring is desired, stain the substrate using Aqua KB-004, Aqua BB-007 or Aqua PB-006.

    • Application
      • Stir before use
      • Airless/airmix spraying / Flow cup gun
      • Application temperature: min. 18 °C max. 25 °C
      • Application requirements

        Temperature of the material, air and substrate: from min. +18 °C to max. +25 °C.

      • Stir well.

        Spray.

        Flow cup gun: nozzle size: 2.0 - 2.5 mm; atomiser air pressure: 2.0 - 3.0 bar.

        Airless spraying: nozzle size: 0.23 - 0.28 mm, material pressure: 80 - 120 bar.

        Airmix spraying: nozzle size: 0.23 - 0.28 mm, material pressure: 80 - 100 bar, atomiser air pressure: 1.2 - 2 bar.

        After drying and intermediate sanding (P 240 - 320), apply a second coat of the product.

        Repeat the process if necessary.

        Seal opened containers well and use contents as soon as possible.

    • Application instructions
      • Drying time: can be worked over after 1.5 h
      • Check colour, adhesion and compatibility with the substrate by setting up a trial area.

      • Drying

        Dust-dry: after approx. 45 minutes Touch-dry: after approx. 60 minutes Can be overcoated: after approx. 1.5 hours Can be stacked: after drying overnight

        Practice values at +20 °C and 65% relative humidity.

        Low temperatures, poor ventilation and high humidity delay drying.

      • Thinning

        Ready to use; if necessary dilute with max. 10% water and/or add max. 3% V-490 as a retarding agent.

    • Working tools / cleaning
      • Airless/airmix spraying / Flow cup gun
      • Airless/airmix spraying equipment, flow cup gun

      • Clean tools with water or Aqua RK-898 Cleaning Concentrate immediately after use.

        Ensure that any residue from cleaning is disposed of correctly.

    • Storage / shelf life
      • Shelf-life 12 months
      • Store frost-free and cool / protect for moisture / close containers
      • If stored unopened in its original container in a cool, dry place and protected against frost, the product will keep for at least 12 months.

    • Usage
      • Approx. 100 - 120 ml / m² per layer applied
      • Approx. 80 - 120 ml/m² per coat

    • Disposal instructions
      • Larger quantities of leftover product should be disposed of in the original containers in accordance with the applicable regulations. Completely empty, clean containers should be recycled. Do not dispose of together with household waste. Do not allow to enter the sewage system. Do not empty into drains.

    • Safety / regulations
      • For further information on the safety aspects of transporting, storing and handling the product and on disposal and environmental matters, please see the current Safety Data Sheet.