Article No. 394105

    Induline LW-725

    Colour: Induline LW-725 | 3941
    Colour: Induline LW-725 | 3941
    Please choose a colour
    Packaging unit

    Product specifications

    The stated values represent typical product characteristics and are not to be construed as binding product specifications.

    Field of application

    • For use on interior and exterior wood
    • Soft and hard woods
    • Dimensionally stable wood building elements: front doors
    • Intermediate and finishing coats
    • AW_IDL_28

    Properties

    • Single component: economical and easy to apply
    • Excellent flow properties
    • High level of UV resistance and colour stability
    • Weather resistant
    • Added bonus of being resistant to scratches and hand cream when surface is subjected to normal use
    • Surfaces show no tendency to become glossy
    • Resistant and long-lasting thanks to a special polyurethane binding agent
    • Very low tendency to develop temporary water stains
    • Compatible with the Induline coating system
    • Preparation
      • Substrate requirements

        The substrate must be clean, dry, free of dust, grease and loose substances, and prepared in the correct manner.

        Dimensionally stable wood building elements: wood moisture content 11-15%

      • Preparations

        If necessary, impregnate non-resistant woods with a wood preservative*.

        Pre-treat using a suitable primer & intermediate coat and carry out intermediate sanding if necessary.

        If necessary, protect parapet joints with Induline V-Joint Protection or Induline AF-920.

    • Application
      • Stir well before using.

        The values given are based on undiluted material. The best spraying pattern is achieved if the material has a temperature of 15-20 °C.

        Airless spraying: nozzle size: 0.28-0.33 mm; material pressure: 70-90 bar.

        Air-mix spraying: nozzle size: 0.28-0.33 mm; material pressure: 70-90 bar, atomiser air pressure 1-2 bar.

        Seal opened containers well and use contents as soon as possible.

    • Application instructions
      • Check colour, adhesion and compatibility with the substrate by setting up a trial area.

        Ensure good ventilation.

        VA2_IDL_37

        Do not use in direct sunlight or at temperatures below +15 °C or above +30 °C.

        Substances in oak may bleed, causing dark discolouration, when coated with water dilutable dispersion stains.

        To prevent any substances in the wood from becoming active, forced drying should be carried out.

        The clear colour version of the product is not suited for use on exterior surfaces that are directly exposed to weather.

        When using a clear intermediate coat, the colours produced may be different to the colours shown on the colour card.

        The system finder on our website www.remmers.com contains coating recommendations for specific wood types to be used when treating windows and exterior doors.

    • Working tools / cleaning
      • Clean tools with water or Aqua RK-898 Cleaning Concentrate immediately after use.

        Ensure that any residue from cleaning is disposed of correctly.

    • Storage / shelf life
      • If stored unopened in its original container in a cool, dry place and protected against frost, the product will keep for at least 12 months.

    • General information
      • Sealing:

        Sealing compounds must be compatible with the coating and may only be applied once the coating has dried thoroughly.

        Only use sealing profiles that are free of plasticisers.

        Production of corrective lacquers:

        In order to repair minor damage to the lacquer (e.g. during installation), mix Induline NW-740/05 with 5% VP 20282 brushable additive (0362).

        Care and maintenance:

        Wood is subjected to great climatic and environmental stresses when outdoors. The coat is susceptible to the processes of natural ageing, wear and decomposition. Decomposition takes place at different speeds, depending on the stress (weak, average, strong) placed on the wood building element. Weathering stages may vary according to the part or element affected. To give wood the longest and best possible protection it is advisable to examine surfaces every year. Any damage found should be addressed immediately after cleaning.

        For cleaning and care, we recommend the care set for doors (2746).

        H_IDL_38

        Observe current standards and guidelines for coating wood building elements outdoors (Codes of Practice issued by the German Association of Window and Facade Manufacturers (VFF), Code of Practice No. 18 issued by the German Federal Committee for Paint and the Protection of Material Assets (BFS), guidelines issued by the German Lacquer and Printing Ink Association (VdL) and ift guidelines issued by the Institut für Fenstertechnik).

    • Disposal instructions
      • Larger quantities of leftover product should be disposed of in the original containers in accordance with the applicable regulations. Completely empty, clean containers should be recycled. Do not dispose of together with household waste. Do not allow to enter the sewage system. Do not empty into drains.

    • Safety / regulations
      • For further information on the safety aspects of transporting, storing and handling the product and on disposal and environmental matters, please see the current Safety Data Sheet.