• 0000297613_Color_Flex
  • 0000297605_Color_Flex
    • 0000297613_Color_Flex
    • 0000297605_Color_Flex

    Article No. 297613

    Color Flex

    Highly elastic facade coating

    Colour: white | 2976
    Colour: white | 2976
    Please choose a colour
    Packaging unit

    Product specifications

    On delivery

    Binder base UV-crosslinking acrylate copolymer
    Density Approx. 1.35 g/cm³
    pH value > 8.5
    Pigmentation Light-fast, alkali-resistant oxide pigments
    Extender Mineral fillers

    Once fully cured

    Once fully cured

    Alkali resistance Up to pH 14
    Degree of gloss Silk matt
    Water vapour permeability
    (DIN EN ISO 7783-2)
    sd ≤ 0.9 m *
    CO2 permeability
    (DIN EN 1062-6)
    sd ≥ 115 m *
    Water absorption coefficient
    (DIN EN 1062-3)
    w ≤ 0.10 kg/(m² ∙ h0.5)
    Surface structure Smooth
    Weather resistance Very good

    Characteristic data of the product

    * These values apply to a dry layer thickness of approx. 500 µ

    The stated values represent typical product characteristics and are not to be construed as binding product specifications.

    Field of application

    • For use outdoors
    • Facades and concrete surfaces
    • Surface protection system for concrete building elements in accordance with DIN EN 1504 / DIN V 18026 according to class OS 5a (OS-DII)
      Remmers OS-DII / OS 5a System:
      Betofix Fill (Betofix Filler) + Color Flex (Elastoflex Facade Paint)
      Remmers OS-DII / OS 5a System:
      Color PA Fill (OS Concre-Fill) + Color Flex (Elastoflex Facade Paint)
    • Load-bearing, adhering old coatings on a mineral or synthetic resin base
    • Cracked facade surfaces

    Properties

    • High crack-bridging capability
    • UV-crosslinking binder
    • Carbonation-inhibiting sd CO₂ ≥ 115 m
    • Highly water-repelling w ≤ 0.1 kg/(m² ∙ h0.5)
    • Water vapour permeable
    • Very good hiding power
    • Approved by the German Federal Highway Research Institute (BASt)
    • Tested in accordance with DIN EN 1504-2
    • Preparation
      • Substrate requirements

        The substrate must be dry, clean, load-bearing and free of dust.

        Free of aggressive salts.

      • Preparations

        Prime load-bearing, mineral substrates with Funcosil BI.

    • Application
      • By brush / By roller / Airless/airmix spraying
      • Application temperature: min. 5 °C max. 30 °C
      • Application requirements

        Temperature of the material, air and substrate: from min. +5 °C to max. +30 °C

      • Stir well.

        Coat the surface using a suitable tool.

        Apply the material in 2 or 3 coats, depending on the condition of the substrate.

        Wait at least 8 hours between coats.

    • Application instructions
      • Take appropriate measures to protect adjacent building elements and materials that should not come into contact with the product.

        Intensive colours, such as yellow, red, etc. may have a lower hiding power due to their pigments. Apply an additional coat if required.

        Protect freshly treated surfaces from driving rain, wind, sunlight and condensation.

    • Working tools / cleaning
      • By brush / By roller / Airless/airmix spraying
      • Brush, surface brush, lamb's wool roller, airless spraying equipment

      • Wash tools and any splashed material with water immediately and while wet.

    • Storage / shelf life
      • Shelf-life 12 months
      • Store frost-free and cool / protect for moisture / close containers
      • If stored unopened in its original container in a cool, dry place and protected against frost, the product will keep for at least 12 months.

    • Usage
      • Total application/absorption rate 750 ml Total / m²
      • Approx. 0.65 l/m² in three coats Results in a total dry layer thickness of approx. 500 µ.

    • General information
      • Deviations from applicable regulations must be agreed separately.

        The relevant test certificates must be observed when planning and carrying out work.

        Primarily lime-based substrates are not suitable for coating.

    • Disposal instructions
      • Larger quantities of leftover product should be disposed of in the original containers in accordance with the applicable regulations. Completely empty, clean containers should be recycled. Do not dispose of together with household waste. Do not allow to enter the sewage system. Do not empty into drains.

    • Safety / regulations
      • For further information on the safety aspects of transporting, storing and handling the product and on disposal and environmental matters, please see the current Safety Data Sheet.