Article No. 182685

    HWS-112 Hard Wax Seal

    Durable, single-component wood sealer for a natural look and two-time application

    Colour: clear | 1826
    Colour: clear | 1826
    Please choose a colour
    Packaging unit

    Product specifications

    On delivery

    Binder Alkyd resin
    Density (20°C) Approx. 0.88 g/cm³
    Odour Characteristic
    Degree of gloss Cloth matt
    Runout time s in DIN 4 cup Approx. 22

    The stated values represent typical product characteristics and are not to be construed as binding product specifications.

    Field of application

    • Wood in living areas
    • Furniture and interior finishing work
    • Wooden floors and stairs
    • Tables and worktops
    • Interior finishing of ships
    • For bath and sauna elements
    • No removal of excess
    • Cork floors
    • Bamboo components

    Properties

    • Quick-drying
    • Resistant to abrasion and scratches
    • Resistant to chemicals: DIN 68861, 1B
    • Slip-resistant
    • Very low tendency to shine
    • Natural look and feel
    • Fire resistant
    • Preparation
      • Substrate requirements

        The substrate must be clean, dry, free of dust, grease and loose substances, and prepared in the correct manner.

        Wood moisture content: 8-12%

        Final wood sanding no finer than P 180

      • Preparations

        Thoroughly remove any dirt, grease and non-adhering old coatings.

        Wash off greasy or resin-rich woods/substrates with WV-891 or V-890.

        If you wish to add colour, prime with Decorative Wax Stain or OB-008.

        If applying a subsequent coating using a roller: intermediate drying time min. 24 hours.

        When sealing old parquet flooring, end-grain wood parquet and installation patterns with the wood grain running in different directions, we recommend pre-treating with OB-008 clear and leaving to dry for at least 48 hours in order to ensure that the substrate is thoroughly saturated and absorbs the material evenly.

    • Application
      • Application requirements

        Temperature of the material, air and substrate: from min. +15°C to max. +25°C

      • Stir well.

        Apply by spraying or with a roller.

        Flow cup gun: nozzle: 1.6 - 1.8 mm; atomiser air pressure: max. 2 bar

        Airless spraying: nozzle size: 0.23 - 0.28 mm, material pressure: 80 - 120 bar.

        Airmix spraying: nozzle 0.23 - 0.28 mm, material pressure: 80 - 100 bar, atomiser air pressure: max. 1 bar.

        After drying and intermediate sanding (P 240 - 320), apply a second coat of the product.

        Observe the waiting times between coats.

        Seal opened containers well and use contents as soon as possible.

    • Application instructions
      • Check colour, adhesion and compatibility with the substrate by setting up a trial area.

        For smoked oak and other exotic woods, Remmers Technical Service must be consulted prior to use and a trial area set up.

        Make sure the area is well ventilated when using indoors.

        Dispose spray dust deposits regularly to avoid ignition of the spray dust.

        Avoid ultra-fine material atomisation and excessive overspray.

        Leave fresh spraying dust to dry before sweeping up.

        The product itself is not self-igniting.

        When sanding wooden surfaces that have been treated with the product, always wear respiratory protection (dust filter mask P2).

        Risk of self-ignition (DGUV information brochure 209-046).

        The product should not be applied at the same work stand as NC-based varnishes or stains. Collect any textiles soiled with the product (e.g. cleaning rags, work clothing) in fire-resistant waste containers and dispose of properly.

      • Drying

        Dust-dry: after approx. 60 minutes Touch-dry: after approx. 3 hours Can be overcoated by spraying: after approx. 6 hours Can be overcoated using a roller: after approx. 14 hours Full loading capacity: after approx. 7 days

        Practice values at +20 °C and 65% relative humidity.

        Low temperatures and high humidity delay drying.

        Drying is dependent on the type of wood and the absorbency of the substrate.

      • Thinning

        Ready to use

    • Working tools / cleaning
      • Short-pile (3-5 mm) velour or mohair roller, flow cup gun, airless/airmix spraying equipment

      • Clean tools immediately after use with V 101 Thinner.

        Ensure that any residue from cleaning is disposed of correctly.

    • Storage / shelf life
      • If stored unopened in its original container in a cool, dry place and protected against frost, the product will keep for at least 12 months.

    • Usage
      • First coat: 70 ml/m² Second coat: 60 ml/m²

    • General information
      • Use breathable materials when packing the coated wood building elements.

        Dust and loose dirt on floors and stairs should be removed regularly using a soft broom or mop.

        For maintenance (including partial maintenance on traffic areas subject to particular levels of wear), treat the cleaned surface with the product or with Hard Wax Oil in such a way that it blends in to produce a uniform finish.

        If necessary, mop once a week with a slightly damp cloth, making sure to add Oiled Floor Care [eco] to the water used for mopping.

        Please refer to the relevant test reports/certificates and the Technical Data Sheet for information on certified products and configurations.

    • Disposal instructions
      • Larger quantities of leftover product should be disposed of in the original containers in accordance with the applicable regulations. Completely empty, clean containers should be recycled. Do not dispose of together with household waste. Do not allow to enter the sewage system. Do not empty into drains.

    • Safety / regulations
      • For further information on the safety aspects of transporting, storing and handling the product and on disposal and environmental matters, please see the current Safety Data Sheet.

    Possible system products