• Induline DW-610
  • Induline DW-610
    • Induline DW-610
    • Induline DW-610

    Article No. 248105

    Induline DW-610

    Water-based, insulating low-build lacquer for primer, intermediate and finishing coat

    Colour: anthracite grey, RAL 7016 | 2481
    Colour: anthracite grey, RAL 7016 | 2481
    Please choose a colour
    Size / Quantity

    Brochures and Catalogues

    product.brochures.loading

    Product specifications

    On delivery

    Binder Special acrylates
    Density (20°C) Approx. 1.28 g/cm³
    Odour Characteristic

    The stated values represent typical product characteristics and are not to be construed as binding product specifications.

    Field of application

    • For use outdoors
    • for elements with limited dimensional stability
    • for not dimensionally stable elements
    • For professional users only
    • For use on exterior wood
    • Wood building elements with limited dimensional stability, e.g. folding shutters, matchboarding, summerhouses
    • Wood building elements with no dimensional stability: e.g. fences, framework, carports, planking
    • Primer, intermediate and finishing coats
    • Especially suited to spruce, fir, Douglas fir, oak, pine and larch

    Properties

    • Water-based
    • Easy to apply
    • Good flow properties
    • Elegant gloss yet maintains the structure of the wood (after three coats)
    • Water vapour diffusion capable
    • Film preserver protects against microbial damage
    • Good resistance to yellowing and chalking
    • Special combination of binding agents creates an extremely hard-wearing surface
    • Does not flake
    • Subsequent treatment without sanding
    • Preparation
      • Substrate requirements

        The substrate must be clean, dry, free of dust, grease and loose substances, and prepared in the correct manner.

        Wood building elements with limited or no dimensional stability: wood moisture content max. 18%

      • Preparations

        Thoroughly remove any dirt, grease and non-adhering old coatings.

        Sand grey and weathered wood surfaces down to sound, bright wood.

        If necessary, impregnate non-resistant woods with a wood preservative* (*Use biocides safely. Always read the label and product information before use).

        Observe BFS Code of Practice No. 18 "Coatings on Wood and Wooden Working Materials in Outdoor Areas".

        Remove any loose and torn knots as well as resin that bleeds from the wood and clean with a suitable product (e.g. V 101 Thinner, a nitrocellulose or universal thinner).

    • Application
      • Temperature of the material, air and substrate: from min. +15 °C to max. +25 °C
      • Stir before use
      • Airless/airmix spraying / Flow cup gun / By brush
      • Application requirements

        Temperature of the material, air and substrate: from min. +15 °C to max. +25 °C.

      • Stir well.

        Apply by brushing or spraying.

        Airless spraying: nozzle size: 0.28 mm, material pressure: 80-120 bar.

        Airmix spraying: nozzle size: 0.28 mm, material pressure: 60-100 bar, atomiser air pressure: 1.2-2.0 bar.

        Flow cup gun: nozzle size: 1.8-2.0 mm, atomiser air pressure: 2-2.5 bar

        Seal opened containers well and use contents as soon as possible.

    • Application instructions
      • Drying time: can be worked over after 4 h
      • Check colour, adhesion and compatibility with the substrate by setting up a trial area.

        Ensure good ventilation.

        For the best possible insulation from soluble substances in wood (surface and knots) the higher values for number of coats, application rates and drying times must be observed. Coating with this product may activate the substances contained in the wood and discolour the paint layer. In this case these substances are fixated inside the paint layer. The follow-up coating should ideally be carried out using a product that supports the insulating properties of this product. This will usually prevent further impairment of this top coat by the substances in the wood. Should discolouration continue to occur despite this advice being followed, we recommend consulting Remmers Technical Service. Bleeding resin is a natural phenomenon and cannot be prevented by coating measures, see BFS Code of Practice No. 18. Dilution of the product, excessive wood moisture, or failure to comply with the recommended coating sequence, application rates and drying times can have a significant negative impact on the insulating effect of the product. Intermediate sanding should go no further than smoothing the wood fibres – the primer must never be sanded away. With water-based coating systems there is always a residual risk of bleeding of substances contained in the wood!

        Do not use in direct sunlight.

      • Drying

        Dust-dry: after approx. 1 hour Can be overcoated: after approx. 4 hours (at 23 °C and 50% RH) If forced drying is used, can be overcoated: after approx. 20 minutes evaporation zone (at approx. 20 °C and 65-75% RH) / 75 minutes drying phase (approx. 45 °C, 1 m/s air circulation) / 20 minutes cooling phase

        Low temperatures, poor ventilation and high humidity delay drying.

      • Thinning

        If necessary, dilute with water (max. 5%).

    • Working tools / cleaning
      • Airless/airmix spraying / Flow cup gun / By brush
      • Airless/Airmix sprayer, flow cup gun, acrylic brush

      • Clean tools with water or Aqua RK-898 Cleaning Concentrate immediately after use.

        Ensure that any residue from cleaning is disposed of correctly.

    • Storage / shelf life
      • Store frost-free and cool / protect for moisture / close containers
      • Shelf-life 12 months
      • If stored unopened in its original container in a cool, dry place and protected against frost, the product will keep for at least 12 months.

    • Usage
      • Approx. 50 ml - 150 ml / m² per layer applied
      • 50-150 ml/m² per coat Brush application: 50-80 ml/m² Spray application: 120-150 ml/m² These values refer to sanded pine. For planed or rough-sawn wood, the values will be lower or correspondingly higher.

    • General information
      • On planed larch and softwoods with a high resin content, the coating may have reduced adhesion and resistance to weathering. This is especially the case on horizontal year rings, knots and areas of winter growth that are high in resin. Maintenance and renovation must be carried out more frequently on these surfaces. The only remedy for this is pre-weathering or very coarse sanding (P80). If these wood types are rough-sawn, considerably longer maintenance and renovation intervals are to be expected.

    • Disposal instructions
      • Larger quantities of leftover product should be disposed of in the original containers in accordance with the applicable regulations. Completely empty, clean containers should be recycled. Do not dispose of together with household waste. Do not allow to enter the sewage system. Do not empty into drains.

    • Safety / regulations
      • For further information on the safety aspects of transporting, storing and handling the product and on disposal and environmental matters, please see the current Safety Data Sheet.