Article No. 637006

    Epoxy BS 3000 M

    Water-based, pigmented, matt sealant

    Colour: special colours from 20 kg | 6370
    Colour: special colours from 20 kg | 6370
    Please choose a colour
    Packaging unit

    Product specifications

    On delivery

    Solids content 68% by mass

    Component A

    Density (20°C) 1.4 g/cm³
    Viscosity (25 °C) 750 mPa s

    Component B

    Density (20°C) 1.1 g/cm³
    Viscosity (25 °C) 750 mPa s

    Mixture

    Density (20°C) 1.4 g/cm³
    Viscosity (25 °C) 1400 mPa s

    The stated values represent typical product characteristics and are not to be construed as binding product specifications.

    Field of application

    • Sealant in Remmers Water Vapour Diffusion-Open systems
    • Topcoat on Remmers Water Vapour Diffusion-Open blinded coatings
    • Sealant and blinded layer in systems approved by the German Institute for Structural Engineering (Deutsches Institut für Bautechnik, DIBt) for recreation rooms (approval area [Abz] Z-156.605-1414)

    Properties

    • Water-based
    • Matt
    • Anti-slipping version possible
    • Water vapour diffusion capable
    • Contains no plasticisers, nonylphenols or alkylphenols
    • Physiologically harmless once fully cured
    • Preparation
      • Substrate requirements

        The substrate must be firm, dimensionally stable, capable of bearing loads and free of loose constituents, dust, oil, grease, rubber marks and other substances that could interfere with adhesion.

        The substrate must be prepared using suitable Remmers Water Vapour Diffusion-Open products.

    • Preparation
      • Mixing ratio comp. A 84 : comp. B 16
      • Mixing time 3 min
      • Combination container

        Add the entire quantity of the hardener (component B) to the basic compound (component A).

        Mix thoroughly with a slow-speed electric mixer
        (approx. 300 - 400 rpm).

        Pour the mixture into a separate container and mix again thoroughly.

        Mix for at least 3 minutes.

        Insufficient mixing is indicated by streaks forming.

    • Application
      • By brush / By roller
      • Pot life 30 min
      • Application temperature: min. 8 °C max. 30 °C
      • Application requirements

        Temperature of the material, air and substrate: from min. +8 °C to max. +30 °C

      • The times given are reduced at higher temperatures and increased at lower temperatures, in particular in combination with high humidity.

    • Working tools / cleaning
      • By brush / By roller
      • Toothed trowel, smoothing trowel, brush, epoxy roller and mixing apparatus

      • More detailed information can be found in the Remmers Tool Programme.

        Clean tools, equipment and any splashed material immediately with water while still fresh.

        Take suitable protective and waste disposal measures when cleaning.

    • Storage / shelf life
      • Store frost-free
      • Shelf-life 9 months
      • LG_A_34

    • Usage
      • See application examples

    • General information
      • Unless otherwise specified, all of the values and application rates given above have been determined under laboratory conditions (20 °C) using standard colours. Slight deviations from these values may arise if the product is worked with on site.

        When coating continuous surfaces, only use materials with the same batch number as slight differences in colour, gloss and texture may occur.

        When repairing surfaces or working up to existing surfaces, there will be a visible transition in appearance, texture and degree of gloss.

        Shades of colour with low hiding power (e.g. yellow, red or orange) tend to have a translucent effect on the subsequently applied sealant. In such cases, a colour-coordinated construction, e.g. light grey, is necessary.

        The sealant has a slightly textured surface typical for this type of system.

        In order to achieve even surfaces, appropriate allowances for roughness depth must be taken into consideration.

        Abrasive mechanical loads leave traces of wear.

        Suitable for vehicle traffic with rubber tyres; not suitable for vehicle loads with metal or polyamide tyres nor for dynamic point loads.

        Epoxy resins are generally not colourfast when exposed to UV light or weather.

        The colour stability of the sealant can be improved by using a UV-absorbent polyurethane sealant.

        Further notes on working, system construction and maintenance of the listed products can be found in the latest Technical Data Sheets and the Remmers system recommendations.

    • Disposal instructions
      • Larger quantities of leftover product should be disposed of in the original containers in accordance with the applicable regulations. Completely empty, clean containers should be recycled. Do not dispose of together with household waste. Do not allow to enter the sewage system. Do not empty into drains.

    • Safety / regulations
      • For professional users only!

        For further information on the safety aspects of transporting, storing and handling the product and on disposal and environmental matters, please see the current Safety Data Sheet and the brochure entitled "Epoxy Resins in the Construction Industry and the Environment", issued by Deutsche Bauchemie e.V. (2nd edition 2009).