• Quartz Primer
  • Quartz Primer
    • Quartz Primer
    • Quartz Primer

    Article No. 281013

    Quartz Primer

    Bonding layer and coating for mineral substrates with low absorbency

    Variant
    2810 | Quartz Primer
    Size / Quantity

    Brochures and Catalogues

    product.brochures.loading

    Product specifications

    Appearance White pigmented
    Density (20°C) Approx. 1.40 g/ml
    Solids content 70%
    Maximum grain size 0.7 mm
    pH value 8
    Viscosity Approx. 2000 mPa
    Water vapour permeability sd value < 0.5 m at 0.25 l/m²
    Carrier material Water

    The stated values represent typical product characteristics and are not to be construed as binding product specifications.

    Field of application

    • For use indoors and outdoors
    • Mineral substrates with low absorbency (in-situ concrete formed with plastic sheet lined formwork, solid slab floors made of building elements, precast concrete unit elements produced with steel formwork)
    • Bonding layer between "render-unfriendly" substrate and the render to be applied
    • Texturing primer
    • On ceramic tiles

    Properties

    • Water-based
    • Increases roughness/non-slip properties
    • Good adhesive power
    • White pigmented
    • Coarse filler
    • Alkali-resistant
    • Preparation
      • Substrate requirements

        Dry, clean, free of dust and cracks (except hairline cracks) and capable of supporting a load.

        Free of salts known to be damaging to building materials.

    • Application
      • Application temperature: min. 5 °C max. 25 °C
      • By brush / By roller / Airless/airmix spraying
      • Application requirements

        Temperature of the material, air and substrate: from min. +5 °C to max. +25 °C

      • Stir well.

        Apply evenly to the material using a brush, roller or spray.

    • Application instructions
      • Structural defects such as cracks, cracked joints, defective connections and rising damp must be remedied first.

        Take appropriate measures to protect adjacent building elements and materials that should not come into contact with the product.

        Please contact Remmers Technical Service (phone +49 5432 83900) before applying with machine processing.

      • Drying

        Ready for next coat after 12 hours at +20 °C and 65% relative humidity.

        As a general principle, higher temperatures will reduce and lower temperatures will increase the times stated.

    • Working tools / cleaning
      • By brush / By roller / Airless/airmix spraying
      • Lambskin roller, flat brush, suitable spraying equipment

      • Clean tools immediately after use with water.

    • Storage / shelf life
      • Store frost-free and cool / protect for moisture / close containers
      • Shelf-life 12 months
      • If stored unopened in its original container in a cool, dry place and protected against frost, the product will keep for at least 12 months.

    • Usage
      • Approx. 250 ml / m² per layer applied
      • Approx. 0.2 - 0.3 l/m² depending on the substrate

      • Apply to a large enough trial area to determine the precise amount required.

    • General information
      • The relevant test certificates must be observed when planning and carrying out work.

        The current technical regulations must be observed.

        Current regulations and legal requirements must be taken into account and deviations from these must be agreed separately.

        Always set up a trial area/trial areas first.

    • Disposal instructions
      • Larger quantities of leftover product should be disposed of in the original containers in accordance with the applicable regulations. Completely empty, clean containers should be recycled. Do not dispose of together with household waste. Do not allow to enter the sewage system. Do not empty into drains.

    • Safety / regulations
      • For further information on the safety aspects of transporting, storing and handling the product and on disposal and environmental matters, please see the current Safety Data Sheet.

    Tools, accessories and PPE