• Color SH

    Article No. 063013

    Color SH

    Mineral paint with fine-grained texture

    Colour: white | 0630
    Colour: white | 0630
    Please choose a colour
    Packaging unit

    Product specifications

    On delivery

    Binder Potassium silicate
    Density (20°C) 1.40 g/cm³
    pH value < 11.5
    Pigmentation UV-stable mineral pigments
    Viscosity Thixotropic

    Once fully cured

    Once fully cured

    Degree of gloss Matt
    UV stability Very good
    Water absorption coefficient
    (DIN 52617)
    w ≤ 0.20 kg/(m² ∙ h0.5)
    Water vapour permeability > 95%
    Water vapour permeability
    (DIN 52615)
    sd ≤ 0.04 m

    The stated values represent typical product characteristics and are not to be construed as binding product specifications.

    Field of application

    • For use outdoors
    • Porous, mineral building materials such as fired and sand-lime brick, sandstone, mineral renders
    • Restoration coat on silicate, lime and cement coatings

    Properties

    • Water-based
    • Quartz-like surface texture
    • Excellent adhesion to substrates
    • Good resistance to weathering
    • Enables water vapour diffusion
    • Repels water
    • With a mineral water base
    • Preparation
      • Substrate requirements

        The substrate must be clean, dust-free and dry.

        Free of salts known to be damaging to building materials.

      • Preparations

        Thoroughly remove any dirt, grease and non-adhering old coatings.

        Any construction defects such as cracks, cracked joints, defective connections, rising damp and hygroscopic moisture must be remedied in advance.

    • Application
      • By brush / By roller / Airless/airmix spraying
      • Application temperature: min. 5 °C max. 25 °C
      • Application requirements

        Temperature of the material, air and substrate: from min. +5 °C to max. +25 °C

      • Stir well.

        Apply evenly to the material using a brush, roller or spray.

        Apply two coats of the material.

        Wait at least 12 hours between coats.

    • Application instructions
      • Take appropriate measures to protect adjacent building elements and materials that should not come into contact with the product.

        To make slight adjustments to the shade of colour, commercially available silicate as well as full strength colour and tinting paints can be used, up to a maximum of 2%.

        Dark and intensive shades of colour may dry to give a slightly mottled finish so it is better to use only pastel shades of colour. The thicker the layer of paint, the lighter the colour dries.

        Do not mix with other products.

        Protect freshly treated surfaces from driving rain, wind, sunlight and condensation.

    • Working tools / cleaning
      • By brush / By roller / Airless/airmix spraying
      • Brush, surface brush, lamb's wool roller, suitable spraying equipment.

      • Clean tools, equipment and any splashed material immediately with water while still fresh.

    • Storage / shelf life
      • Shelf-life 12 months
      • Store frost-free and cool / protect for moisture / close containers
      • If stored unopened in its original container in a cool, dry place and protected against frost, the product will keep for at least 12 months.

    • Usage
      • Total application/absorption rate 400 ml Total / m²
      • Approx. 200 ml/m² per coat depending on the substrate properties.

      • 2 coats required.

        The application rate depends on the absorbency of the surface

        Apply to a large enough trial area to determine the precise amount required.

    • General information
      • Deviations from applicable regulations must be agreed separately.

        The relevant test certificates must be observed when planning and carrying out work.

        Observe the BFS Leaflets for the relevant work areas.

    • Disposal instructions
      • Larger quantities of leftover product should be disposed of in the original containers in accordance with the applicable regulations. Completely empty, clean containers should be recycled. Do not dispose of together with household waste. Do not allow to enter the sewage system. Do not empty into drains.

    • Safety / regulations
      • For further information on the safety aspects of transporting, storing and handling the product and on disposal and environmental matters, please see the current Safety Data Sheet.

    Possible system products