• PC Primer 2K

    Article No. 090001

    PC Primer 2K

    Solvent-free, 2-component epoxy resin

    Variant
    0900 | PC Primer 2K
    Size / Quantity

    Note: This container size is being phased out and is only available to a limited extent.

    Product specifications

    Component A

    Density (20°C) 1.12 g/cm³
    Viscosity (25 °C) 870 mPa s

    Component B

    Density (20°C) 1.03 g/cm³
    Viscosity (25 °C) 200 mPa s

    Mixture

    Density (20°C) 1.10 g/cm³
    Viscosity (25 °C) 600 mPa s

    Once fully cured

    Flexural tensile strength > 46 N/mm²
    Compressive strength > 55 N/mm²

    The stated values represent typical product characteristics and are not to be construed as binding product specifications.

    Field of application

    • For the production of bonding layers when repairing concrete

    Properties

    • Adhesion promoter
    • Solvent-free
    • Unpigmented
    • Liquid
    • Two-component
    • Preparation
      • Substrate requirements

        The substrate must be firm, dimensionally stable, capable of bearing loads and free of loose constituents, dust, oil, grease, rubber marks and other substances that could interfere with adhesion.

        The tensile strength of the surface of the substrate must be at least 1.5 N/mm² on average (smallest individual value of at least 1.0 N/mm²), and the compressive strength must be at least 25 N/mm².

    • Preparation
      • Mixing ratio comp. A 75 : comp. B 25
      • Mixing time 3 min
      • Combination container

        Add the entire quantity of the hardener (component B) to the base compound (component A).

        Mix thoroughly with a slow-speed electric mixer
        (approx. 300 - 400 rpm).

        Pour the mixture into a separate container and mix again thoroughly.

        Mix for at least 3 minutes.

        Insufficient mixing is indicated by streaks forming.

    • Application
      • Application temperature: min. 8 °C max. 25 °C
      • Brush
      • Pot life 25 min
      • Application requirements

        Temperature of the material, air and substrate: from min. +8 °C to max. +25 °C

      • As a general principle, higher temperatures will reduce and lower temperatures will increase the times stated.

        All follow-up working steps must be carried out wet-on-wet.

    • Working tools / cleaning
      • Brush
      • Brush, suitable mixing apparatus

      • More detailed information can be found in the Remmers Tool Programme.

        Clean tools, equipment and splashed material immediately while fresh with V 101.

        Take suitable protective and waste disposal measures when cleaning.

    • Storage / shelf life
      • Store frost-free
      • Shelf-life 12 months
      • If stored unopened in its original container in a cool, dry place and protected against frost, the product will keep for at least 12 months.

    • General information
      • Unless otherwise specified, all of the values and application rates given above have been determined under laboratory conditions (20 °C). Slight deviations from these values may arise if the product is worked with on site.

        Only for use on small surface areas!

        Primers must always be applied so that all pores are filled; it may therefore be necessary to increase the application rate or to apply a second coat.

        Epoxy resins are generally not colourfast when exposed to UV light or weather.

        Further notes on working, system construction and maintenance of the listed products can be found in the latest Technical Data Sheets and the Remmers system recommendations.

    • Safety / regulations
      • For professional users only!

        For further information on the safety aspects of transporting, storing and handling the product and on disposal and environmental matters, please see the current Safety Data Sheet and the brochure entitled "Epoxy Resins in the Construction Industry and the Environment", issued by Deutsche Bauchemie e.V. (3rd edition 2022).

    Possible system products

    Tools, accessories and PPE