• PUR Top TX
  • PUR Top TX Comp-A
  • PUR Top TX Comp-B
  • PUR Top TX
    • PUR Top TX
    • PUR Top TX Comp-A
    • PUR Top TX Comp-B
    • PUR Top TX

    Article No. 633004

    PUR Top TX

    Textured, transparent seal coat

    Colour: clear | 6330
    Size / Quantity

    Product specifications

    Component A

    Density (20°C) 1.1 g/cm³

    Component B

    Density (20°C) 1.0 g/cm³


    Density (20°C) 1.1 g/cm³

    The stated values represent typical product characteristics and are not to be construed as binding product specifications.

    Field of application

    • Sealant for surfaces subjected to mechanical stresses


    • Textured
    • Matt surface
    • UV-resistant
    • Can be subjected to mechanical loads
    • Can be subjected to chemical loads
    • Can be pigmented if necessary
    • Preparation
      • Preparations

        The seal coat must be applied within 48 hours of applying the underlying layer.

    • Preparation
      • Mixing ratio comp. A 90 : comp. B 10
      • Mixing time 3 min
      • Combination container

        Add the entire quantity of the hardener (component B) to the base compound (component A).

        Mix thoroughly with a slow-speed electric mixer
        (approx. 300 - 400 rpm).

        Pour the mixture into a separate container and mix again thoroughly.

        Mix for at least 3 minutes.

        Insufficient mixing is indicated by streaks forming.

    • Application
      • Application temperature: min. 10 °C max. 25 °C
      • By roller
      • Pot life 30 min
      • Higher temperatures and higher absolute humidity reduce the specified times, while lower temperatures and lower absolute humidity increase them.

    • Working tools / cleaning
      • By roller
      • Epoxy roller, PU roller, mixing equipment

      • More detailed information can be found in the Remmers Tool Programme.

        Clean tools, equipment and splashed material immediately while fresh with V 101.

        Take suitable protective and waste disposal measures when cleaning.

    • Storage / shelf life
      • Store frost-free
      • Shelf-life 12 months
      • If stored unopened in its original container in a cool, dry place and protected against frost, the product will keep for at least 12 months.

    • Usage
      • Max. 0.10 kg/m²

    • Application examples
      • Sealant

        Apply the material to the surface and apply evenly with a suitable 25 cm PU roller in a crosswise motion. Immediately after application, roll the material in one direction with a 50 cm epoxy roller without applying pressure.

        Staggered application is recommended for pre-coating in order to keep the application times as short as possible.

        Always work wet-on-wet.

        max. 0.10 kg/m²

    • General information
      • Unless otherwise specified, all of the values and application rates given above have been determined under laboratory conditions (20 °C). Slight deviations from these values may arise if the product is worked with on site.

        Use sufficiently experienced personnel to ensure that surfaces are as even as possible.

        If the processing time is exceeded, roller marks or differences in degree of gloss and colour may occur.

        When coating continuous surfaces, only use materials with the same batch number as slight differences in colour, gloss and texture may occur.

        In case of repairs on the surface or working up to existing surfaces, there will be a visible transition in appearance and texture.

        Uneven application and large temperature differences on the surface may lead to a non-uniform surface appearance due to differences in the degree of gloss.

        Excessively thick layers, sweat drops or dripping material will cause the sealant to foam up.

        Abrasive mechanical loads leave traces of wear.

        Suitable for vehicle traffic with rubber tyres; not suitable for vehicle loads with metal or polyamide tyres nor for dynamic point loads.

        Further notes on working, system construction and maintenance of the listed products can be found in the latest Technical Data Sheets and the Remmers system recommendations.

    • Disposal instructions
      • Larger quantities of leftover product should be disposed of in the original containers in accordance with the applicable regulations. Completely empty, clean containers should be recycled. Do not dispose of together with household waste. Do not allow to enter the sewage system. Do not empty into drains.

    • Safety / regulations
      • For professional users only!

        Further information concerning safety during transport, storage and handling as well as on disposal and ecology can be found in the latest Safety Data Sheet.

    Tools, accessories and PPE