• Aqua VL-66/sm

    Article No. 709001

    Aqua VL-66/sm-Venti Coat 3in1

    Water-based one-pot coating system with a sealing effect for high-value wooden structures

    Button EN 71/3 Schaukelpferd Button 3in1 Lack Button remmers-mix
    Colour: white (RAL 9016) | 7090
    Colour: white (RAL 9016) | 7090
    Please choose a colour

    Product specifications

    On delivery

    Density (20°C) approx. 1.27 g/cm³
    Odour mild
    Viscosity approx. 1800 mPa∙s

    The stated values represent typical product characteristics and are not to be construed as binding product specifications.

    Field of application

    • For use indoors and outdoors
    • for dimensionally stable elements
    • for elements with limited dimensional stability
    • for not dimensionally stable elements
    • For professional users only
    • For use on interior and exterior wood
    • Dimensionally stable wood building elements: e.g. windows and doors
    • Wood building elements with limited dimensional stability, e.g. folding shutters, matchboarding, summerhouses
    • Wood building elements with no dimensional stability: e. g. fences, framework, carports, planking

    Properties

    • Water-based
    • Water-based
    • Base coat, intermediate coat and topcoat all in one
    • Ventilating effect
    • Block resistant (in accordance with Code of Practice HO.03)
    • Resistant to extreme temperatures and little tendency to yellow
    • Silk matt
    • Isolating effect against substances contained in the wood
    • Inhibits rust from screws and nail heads
    • Highly weather-resistant and low-chalking
    • Preparation
      • Substrate requirements

        Dimensionally stable wood building elements: wood moisture content 11-15%

        Wood building elements with limited or no dimensional stability: wood moisture content max. 18%

      • Preparations

        Thoroughly remove any dirt, grease and non-adhering old coatings.

        Thoroughly sand any old coatings that are still intact.

        Sand grey and weathered wood surfaces down to sound, bright wood.

        Aqua IG-15 Impregnation Primer IT* should be used to pre-treat wood in outdoor areas which requires protection against insects, rot and blue stain (omit step for wood in indoor areas).

        Observe BFS Code of Practice No. 18 "Coatings on Wood and Wooden Working Materials in Outdoor Areas".

    • Application
      • Stir before use
      • By brush / By roller Airless/airmix spraying / Flow cup gun
      • Application temperature: min. 5 °C max. 25 °C
      • Application requirements

        Temperature of the material, air and substrate: from min. +5 °C to max. +25 °C

      • Stir well.

        Apply with a brush, roller or by spraying.

        Flow cup gun: nozzle size: 2.0 - 2.5 mm; atomiser air pressure: 2.0 - 3.0 bar.

        Airless spraying: nozzle size: 0.23 - 0.28 mm, material pressure: 80 - 120 bar.

        Airmix spraying: nozzle size: 0.23 - 0.28 mm, material pressure: 80 - 100 bar, atomiser air pressure: 1.2 - 2 bar.

        Re-coat once dry.

        Seal opened containers well and use contents as soon as possible.

    • Application instructions
      • Drying time: can be worked over after 6 h
      • Areas that are being coated or dried should be protected against rain, wind, sunlight and condensation.

        Check the product’s compatibility with the substrate and its insulating effect by applying a trial coat.

        The colour shown on the sample does not appear until the material has dried.

      • Drying

        Dust dry: after 1–2 hours Can be overcoated: after approx. 6 hours

        Practice values at +20 °C and 65% relative humidity.

        The coating may take significantly longer to dry thoroughly in lower temperatures, at high humidity or if the maximum layer thickness has been exceeded.

        Longer drying times can improve the insulating effect.

      • Thinning

        Ready to use

    • Working tools / cleaning
      • By brush / By roller Airless/airmix spraying / Flow cup gun
      • Acrylic brush/synthetic fibre brush, microfibre paint roller, flow cup or airless spraying equipment

      • Clean tools immediately after use with water and detergent.

        Ensure that any residue from cleaning is disposed of correctly.

    • Storage / shelf life
      • Shelf-life 12 months
      • Store frost-free and cool / protect for moisture / close containers
      • If stored unopened in its original container in a cool, dry place and protected against frost, the product will keep for at least 12 months.

    • Usage
      • Approx. 100 - 120 ml / m² per layer applied
      • 100-120 ml/m² per coat 2 coats are required to seal off substances contained in the wood.

    • General information
      • Insulation of resins and substances contained in the wood.

        The instructions regarding coats, application volumes and drying times for the coating system must be followed to ensure the best possible insulation for water-soluble substances contained in the wood (flat surfaces and branches). The first coat can activate substances in the wood and discolour the film on the coating, which will lock the substances inside the film. The second coat of insulating product will then seal off the substances contained in the wood.

        At least two coats of the product are required to achieve an efficient insulating effect.

        If discolouration continues even after following these steps, we recommend contacting our RTS (Remmers Technical Service).

        Bleeding resin is a natural phenomenon and cannot be prevented by coating measures, see BFS Code of Practice No. 18.

        The product’s insulating effect may be impaired if it is diluted too thinly, if the wood is too wet or if the recommended coating sequence, application volumes and drying times are not observed. With water-based coating systems, there is always the residual risk that substances contained in the wood will leach out.

    • Disposal instructions
      • Larger quantities of leftover product should be disposed of in the original containers in accordance with the applicable regulations. Completely empty, clean containers should be recycled. Do not dispose of together with household waste. Do not allow to enter the sewage system. Do not empty into drains.

    • Safety / regulations
      • For further information on the safety aspects of transporting, storing and handling the product and on disposal and environmental matters, please see the current Safety Data Sheet.