• Induline DW-625
  • Induline DW-625
    • Induline DW-625
    • Induline DW-625

    Article No. 176405

    Induline DW-625

    Water-based, opaque intermediate and final coat for front doors with increased resistance to scratches and hand cream

    Button EN 71/3 Schaukelpferd Button remmers-mix
    Colour: white (RAL 9016) | 1764
    Colour: white (RAL 9016) | 1764
    Please choose a colour
    Packaging unit

    Product specifications

    On delivery

    Binder PU polymers
    Density (20°C) 1.19 g/cm³
    Odour Characteristic
    Degree of gloss Matt/silk gloss
    Viscosity Approx. 2800 mPas

    The stated values represent typical product characteristics and are not to be construed as binding product specifications.

    Field of application

    • For use indoors and outdoors
    • for exterior doors
    • For professional users only
    • For use on interior and exterior wood
    • Dimensionally stable wood building elements: front doors
    • Intermediate and finishing coats
    • Textured varnishes can be produced by adding SM-820.

    Properties

    • Water-based
    • Single component: economical and easy to apply
    • Excellent flow properties
    • Good resistance to yellowing and chalking
    • Weather resistant
    • Added bonus of being resistant to scratches and hand cream when surface is subjected to normal use
    • Good resistance to metal rings
    • Surfaces show no tendency to become glossy
    • Resistant and long-lasting thanks to a special polyurethane binding agent
    • Very low tendency to develop temporary water stains
    • Compatible with the Induline coating system
    • Preparation
      • Substrate requirements

        Dimensionally stable wood building elements: wood moisture content 11-15%

        The substrate must be clean, dry, free of dust, grease and loose substances, and prepared in the correct manner.

      • Preparations

        If necessary, impregnate non-resistant woods with a wood preservative*.

        Pre-treat using a suitable primer & intermediate coat and carry out intermediate sanding if necessary.

        If necessary, protect parapet joints with Induline V-Joint Protection or Induline AF-920.

    • Application
      • Stir before use
      • Airless/airmix spraying
      • Temperature of the material, air and substrate: from min. +15 °C to max. +30 °C
      • Application requirements

        Temperature of the material, air and substrate: from min. +15 °C to max. +30 °C.

      • Stir well before using.

        The values given are based on undiluted material. The best spraying pattern is achieved if the material has a temperature of 15-20 °C.

        Ensure good ventilation.

        Check colour and compatibility with the substrate by applying a trial coat.

        Airless spraying: nozzle size: 0.28-0.33 mm; material pressure: 70-90 bar.

        Air-mix spraying: nozzle size: 0.28-0.33 mm; material pressure: 70-90 bar, atomiser air pressure 1-2 bar.

        Seal opened containers well and use contents as soon as possible.

    • Application instructions
      • Drying time: can be worked over after 4 h
      • Check colour, adhesion and compatibility with the substrate by setting up a trial area.

        Do not use in direct sunlight or at temperatures below +15 °C or above +30 °C.

        The viscosity of the product may vary considerably depending on the colour selected. These variations are due to the pigment and usually only have a very minor impact on the stability.

        To prevent coloured substances contained in the wood from showing through, use a suitable primer and intermediate coating with a sealing effect on white or light-coloured surfaces.

        With water based coating systems, there is always a residual risk that substances contained in the wood will cause discoloration.

        The system finder on our website www.remmers.de contains coating recommendations for specific wood types to be used when treating windows and exterior doors.

        To avoid thicker coats, e.g. in the case of full-tone colours, pretreat with translucent rather than white primer. Then add the coloured topcoat as the intermediate coat.

        For the best spraying results, use a nozzle size of 0.28 mm and pressure of 90 bar.

      • Drying

        Dust-dry: after approx. 1 hour Can be sanded and overcoated: after approx. 4 hours (at 23 °C and 50% RH) If forced drying is used, can be sanded and overcoated: after 20 minutes evaporation zone (at approx. 20 °C and 65 - 75% RH) / 75 minutes drying phase (approx. 45°C, 1 m/s air circulation) / 20 minutes cooling phase

      • Thinning

        If necessary with water (max. 5%).

    • Working tools / cleaning
      • Airless/airmix spraying
      • Manual spray gun, automatic spraying equipment

      • Clean tools with water or Aqua RK-898 Cleaning Concentrate immediately after use.

        Ensure that any residue from cleaning is disposed of correctly.

    • Storage / shelf life
      • Shelf-life 12 months
      • Store frost-free and cool / protect for moisture / close containers
      • If stored unopened in its original container in a cool, dry place and protected against frost, the product will keep for at least 12 months.

    • Usage
      • Approx. 150 ml - 200 ml / m² per layer applied
      • 150 - 200 ml/m² (plus spraying loss) (corresponds to a wet film thickness: 150 - 200 µm, dry layer thickness: 55 - 70 µm)

    • Application examples
      • Textured varnishes can be produced by adding SM-820 Texturing Agent. This has a special haptic quality, a lower gloss level, and even higher mechanical resistance. When the texturing agent is added after mixing with water, it must be noted that the coating will have a lower stability. If the texturing agent is not mixed with water, it must be slowly added while stirring constantly with the Remmers Patent Disperser. Induline DW-625 with Texturing Agent SM-820/M or SM-820/S can be worked using a cup gun, nozzle size 2.5 mm, and in airless/airmix procedures with a nozzle size of 0.28 mm/0.11 in with a white push-in filter. Texturing Agent SM-820/L should be worked using a cup gun, nozzle size 2.5 mm, or an airless/airmix procedure with a nozzle size of 0.33 mm/0.13 in with a white push-in filter. After applying Induline DW-625 with SM-820 added, the spraying equipment used must be thoroughly washed with water to ensure that no SM-820 residues remain in the tool. For further information on the use of SM-820, please see the relevant Technical Data Sheet.

    • General information
      • Sealing:

        Sealing compounds must be compatible with the coating and may only be applied once the coating has dried thoroughly.

        Only use sealing profiles that are free of plasticisers.

        Production of corrective lacquers:

        In order to repair minor damage to the lacquer (e.g. during installation), mix Induline NW-740/05 with 5% VP 20282 brushable additive (0362).

        Care and maintenance:

        Wood is subjected to great climatic and environmental stresses when outdoors. The coat is susceptible to the processes of natural ageing, wear and decomposition. Decomposition takes place at different speeds, depending on the stress (weak, average, strong) placed on the wood building element. Weathering stages may vary according to the part or element affected. To give wood the longest and best possible protection it is advisable to examine surfaces every year. Any damage found should be addressed immediately after cleaning.

        For cleaning and care, we recommend the care set for doors (2746).

        Apply a reconditioning coat of Aqua AG-26 All Primer and Aqua DL-65 Opaque Top PU.

        Observe current standards and guidelines for coating wood building elements outdoors (Codes of Practice issued by the German Association of Window and Facade Manufacturers (VFF), Code of Practice No. 18 issued by the German Federal Committee for Paint and the Protection of Material Assets (BFS), guidelines issued by the German Lacquer and Printing Ink Association (VdL) and ift guidelines issued by the Institut für Fenstertechnik).

    • Disposal instructions
      • Larger quantities of leftover product should be disposed of in the original containers in accordance with the applicable regulations. Completely empty, clean containers should be recycled. Do not dispose of together with household waste. Do not allow to enter the sewage system. Do not empty into drains.

    • Safety / regulations
      • For further information on the safety aspects of transporting, storing and handling the product and on disposal and environmental matters, please see the current Safety Data Sheet.