Article No. 142511

    Epoxy WHG Color

    Chemically resistant, crack-bridging coating

    Zulassung 59.12-302
    Colour: light grey | 1425
    Colour: light grey | 1425
    Please choose a colour
    Packaging unit

    Product specifications

    On delivery

    Component A

    Density (20°C) 1.72 g/cm³
    Viscosity (25 °C) 4300 mPa s

    Component B

    Density (20°C) 1.05 g/cm³
    Viscosity (25 °C) 480 mPa s

    Mixture

    Density (20°C) 1.55 g/cm³
    Viscosity (25 °C) 2100 mPa s

    Once fully cured

    Once fully cured

    Flexural tensile strength Approx. 17 N/mm² *
    Compressive strength Approx. 45 N/mm² *
    Shore D after 28 days 59

    Characteristic data of the product

    * Epoxy resin mortar 1 : 10 with standard sand

    The stated values represent typical product characteristics and are not to be construed as binding product specifications.

    Field of application

    • Chemically resistant, crack-bridging coating
    • Coating in the SL Floor WHG system (GTA Z-59.12-302)

    Properties

    • With static crack-bridging ability
    • Highly resistant to chemicals
    • Fire resistant
    • Suitable for hand pallet trucks and forklift trucks
    • Preparation
      • Substrate requirements

        The substrate must be firm, dimensionally stable, capable of bearing loads and free of loose constituents, dust, oil, grease, rubber marks and other substances that could interfere with adhesion.

        The adhesive pull strength of the surface after priming must be at least 1.5 N/mm² on average (smallest single value min. 1.0 N/mm²), compressive strength at least 25 N/mm².

        Suitable Remmers epoxy primers, epoxy scratch coats or epoxy mortars must always be used.

        Refer to the current Technical Data Sheet for detailed information on the single products.

        For works within the framework of the general building inspectorate approval, the substrates must correspond to the requirements of the approval and the system products mentioned therein must be used.

    • Preparation
      • Mixing ratio comp. A 100 : comp. B 20
      • Mixing time 3 min
      • Combination container

        Add the entire quantity of the hardener (component B) to the basic compound (component A).

        Mix thoroughly with a slow-speed electric mixer
        (approx. 300 - 400 rpm).

        Pour the mixture into a separate container and mix again thoroughly.

        Mix for at least 3 minutes.

        Insufficient mixing is indicated by streaks forming.

    • Application
      • Self-levelling coating / Apply standing
      • Pot life 45 min
      • Application temperature: min. 10 °C max. 30 °C
      • Application requirements

        Temperature of material, surroundings and substrate: min. +10 °C to max. +30 °C.

      • As a general principle, higher temperatures will reduce and lower temperatures will increase the times stated.

    • Working tools / cleaning
      • Self-levelling coating / Apply standing
      • Toothed trowel, toothed spreader, spiked roller (metal), rubber squeegee, epoxy roller, suitable mixing apparatus

      • More detailed information can be found in the Remmers Tool Programme.

        Clean tools, equipment and splashed material immediately while fresh with V 101 Thinner.

        Take suitable protective and waste disposal measures when cleaning.

    • Storage / shelf life
      • Store frost-free
      • Shelf-life 12 months
      • If stored unopened in its original container in a cool, dry place and protected against frost, the product will keep for at least 12 months.

    • Usage
      • See application examples

    • General information
      • Unless otherwise specified, all of the values and application rates given above have been determined under laboratory conditions (20 °C) using standard colours. Slight deviations from these values may arise if the product is worked with on site.

        When coating continuous surfaces, only use materials with the same batch number as slight differences in colour, gloss and texture may occur.

        Application of the mixture by toothed trowel/toothed spreader. If the product is applied with a smoothing trowel/screed levelling tool, trowel marks may be visible on the finished surface.

        In case of repairs on the surface or working up to existing surfaces, there will be a visible transition in appearance and texture.

        Abrasive mechanical loads leave traces of wear.

        Exposure to vehicles with metal or polyamide tyres as well as dynamic concentrated loads can cause faster wearing of the coating.

        Epoxy resins are generally not colourfast when exposed to UV light or weather.

        Further notes on working, system construction and maintenance of the listed products can be found in the latest Technical Data Sheets and the Remmers system recommendations.

    • Safety / regulations
      • For professional users only!

        For further information on the safety aspects of transporting, storing and handling the product and on disposal and environmental matters, please see the current Safety Data Sheet and the brochure entitled "Epoxy Resins in the Construction Industry and the Environment", issued by Deutsche Bauchemie e.V. (2nd edition 2009).

    Possible system products