Article No. 714701
Adhesive primer for metals, rigid plastics and wood, with rust protection and sealing action against substances contained in wood
The stated values represent typical product characteristics and are not to be construed as binding product specifications.
Dimensionally stable wood building elements: wood moisture content 11-15%
Wood building elements with limited or no dimensional stability: wood moisture content max. 18%
Thoroughly remove any dirt, grease and non-adhering old coatings.
Sand grey and weathered wood surfaces down to sound, bright wood.
Remove any loose and torn knots as well as resin that bleeds from the wood and clean with a suitable product (e.g. V 101 Thinner).
Aqua IG-15 Impregnation Primer IT* should be used to pre-treat wood in outdoor areas which requires protection against insects, rot and blue stain (omit step for wood in indoor areas).
Observe BFS Code of Practice No. 18 "Coatings on Wood and Wooden Working Materials in Outdoor Areas".
Wash off greasy or resin-rich woods/substrates with WV-891 or V-890.
Softwoods: sand with P 80 - 120.
All other substrates: sand with P 180 - 320.
Derust thoroughly. Remove scale layers and rolling skin (derust manually to SA 3 standard of cleanliness). The best results are achieved if the substrate has been sand blasted to SA 2.5 standard of cleanliness (DIN EN ISO 12944-4).
Zinc (galvanised steel):
Clean with an ammonium-based wetting agent, using an abrasive pad. Observe BFS Code of Practice No. 5.
Clean with V 101 or V-890 thinner, or a cleaning agent that contains phosphoric acid. Observe BFS Code of Practice No. 6.
Treat rigid PVC, PUR, polyester, acrylic, and melamine resin coatings (Resopal) with V 101 or V-890 thinner and an abrasive pad.
Temperature of the material, air and substrate: from min. +5 °C to max. +25 °C
Apply with a brush, roller or by spraying.
After drying and intermediate sanding, coat with a water-based or solvent-based lacquer.
Observe the waiting times between coats.
Check the product’s compatibility with the substrate and its insulating effect by applying a trial coat.
Dust-dry: approx. 4 hours Overcoating: approx. 12 hours
Practice values at +20 °C and 65% relative humidity.
For faster drying, the coated object can be dried in a drying chamber up to a temperature of 60 °C.
Low temperatures, poor ventilation and high humidity delay drying.
Longer drying times can improve the insulating effect.
With up to 5% water if required.
Acrylic brush/synthetic fibre bristles, microfibre paint roller, flow cup gun
Clean tools with water or Aqua RK-898 Cleaning Concentrate immediately after use.
Ensure that any residue from cleaning is disposed of correctly.
If stored unopened in its original container in a cool, dry place and protected against frost, the product will keep for at least 24 months.
100 ml/m² per coat 2 coats are required for corrosion protection and sealing action against substances contained in wood.
Insulation of resins and substances contained in the wood.
The instructions regarding coats, application volumes and drying times for the coating system must be followed to ensure the best possible insulation for water-soluble substances contained in the wood (flat surfaces and branches). The first coat can activate substances in the wood and discolour the film on the coating, which will lock the substances inside the film. The second coat of insulating product will then seal off the substances contained in the wood.
Subsequent finish coats are then usually no longer affected by substances contained in the wood.
At least two coats of the product are required to achieve an efficient insulating effect.
If discolouration continues even after following these steps, we recommend contacting our RTS (Remmers Technical Service).
Bleeding resin is a natural phenomenon and cannot be prevented by coating measures, see BFS Code of Practice No. 18.
The product’s insulating effect may be impaired if it is diluted too thinly, if the wood is too wet or if the recommended coating sequence, application volumes and drying times are not observed. With water-based coating systems, there is always the residual risk that substances contained in the wood will leach out.
Check colour, adhesion and compatibility with the substrate by setting up a trial area.
Larger quantities of leftover product should be disposed of in the original containers in accordance with the applicable regulations. Completely empty, clean containers should be recycled. Do not dispose of together with household waste. Do not allow to enter the sewage system. Do not empty into drains.
For further information on the safety aspects of transporting, storing and handling the product and on disposal and environmental matters, please see the current Safety Data Sheet.