• Induline LW-715E

    Article No. 179805

    Induline LW-715E

    Water-based, varnishing intermediate and final coat especially suited to electrostatic spraying

    Button remmers-mix Button VOC FR A+
    Colour: clear | 1798
    Colour: clear | 1798
    Please choose a colour
    Packaging unit

    Product specifications

    On delivery

    Binder Spec. PU/acrylate polymers
    Density (20°C) Approx. 1.04 g/cm³
    Odour Characteristic
    Viscosity Approx. 2000 mPa∙s

    The stated values represent typical product characteristics and are not to be construed as binding product specifications.

    Field of application

    • For use indoors and outdoors
    • for dimensionally stable elements
    • For professional users only
    • For use on interior and exterior wood
    • Soft and hard woods
    • Dimensionally stable wood building elements: e.g. windows and doors
    • Protected constructions: e.g. wood-aluminium windows
    • Intermediate and finishing coats
    • Single coat and multi-coat procedure

    Properties

    • Water-based
    • Good flow properties
    • UV-resistant and colourfast
    • Block resistant (in accordance with Code of Practice HO.03)
    • Special combination of binding agents creates an extremely hard-wearing surface
    • Preparation
      • Substrate requirements

        The substrate must be clean, dry, free of dust, grease and loose substances, and prepared in the correct manner.

        Dimensionally stable wood building elements: wood moisture content 11-15%

      • Preparations

        If necessary, impregnate non-resistant woods with a wood preservative*.

        Pre-treat using a suitable primer & intermediate coat and carry out intermediate sanding if necessary.

        If necessary, protect parapet joints with Induline V-Joint Protection or Induline AF-920.

    • Application
      • Stir before use
      • Airless/airmix spraying
      • Temperature of the material, air and substrate: from min. +15 °C to max. +30 °C
      • Application requirements

        Temperature of the material, air and substrate: from min. +15 °C to max. +30 °C.

      • The values given are based on undiluted material. The best spraying pattern is achieved if the material has a temperature of 15-20 °C.

        Stir well.

        Airless spraying: nozzle size: 0.28-0.33 mm; material pressure: 70-90 bar.

        Air-mix spraying: nozzle size: 0.28-0.33 mm; material pressure: 70-90 bar, atomiser air pressure 1-2 bar.

        Seal opened containers well and use contents as soon as possible.

    • Application instructions
      • Drying time: can be worked over after 4 h
      • Check colour, adhesion and compatibility with the substrate by setting up a trial area.

        Ensure good ventilation.

        Do not use in direct sunlight or at temperatures below +15 °C or above +30 °C.

        Substances in oak may bleed, causing dark discolouration, when coated with water dilutable dispersion stains.

        To prevent any substances in the wood from becoming active, forced drying should be carried out.

        The clear colour version of the product is not suited for use on exterior surfaces that are directly exposed to weather.

        When using a clear intermediate coat, the colours produced may be different to the colours shown on the colour card.

      • Drying

        Dust-dry: after approx. 1 hour Can be sanded and overcoated: after approx. 4 hours (at 23 °C and 50% RH) If forced drying is used, can be sanded and overcoated: after 20 minutes evaporation zone (at approx. 20 °C and 65 - 75% RH) / 75 minutes drying phase (approx. 45 °C, 1 m/s air circulation) / 20 minutes cooling phase.

        If the temperature goes below the specified working temperature or exceeds the specified atmospheric humidity or maximum coat thickness, this will delay full drying and lead to inclusion of hydrophilic emulsifiers. This increases the risk of temporary water staining. This effect is reduced as the coat continues to harden.

      • Thinning

        If necessary with water (max. 5%).

    • Working tools / cleaning
      • Airless/airmix spraying
      • Manual spray gun, automatic spraying facility.

      • Clean tools with water or Aqua RK-898 Cleaning Concentrate immediately after use.

        Ensure that any residue from cleaning is disposed of correctly.

    • Storage / shelf life
      • Shelf-life 12 months
      • Store frost-free and cool / protect for moisture / close containers
      • If stored unopened in its original container in a cool, dry place and protected against frost, the product will keep for at least 12 months.

    • Usage
      • Approx. 150 ml - 275 ml / m² per layer applied
      • 150 - 275 ml/m² (plus spraying loss) (corresponds to wet film thickness: 150 - 275 µm, dry film thickness: 50 - 100 µm)

    • General information
      • Sealing:

        Sealing compounds must be compatible with the coating and may only be applied once the coating has dried thoroughly.

        Only use sealing profiles that are free of plasticisers.

        Production of a brushing quality:

        This product can be used with Induline Mix & Go to produce an easy-to-apply lacquer for reconditioning and repair work.

        Care and maintenance:

        Wood is subjected to great climatic and environmental stresses when outdoors. The coat is susceptible to the processes of natural ageing, wear and decomposition. Decomposition takes place at different speeds, depending on the stress (weak, average, strong) placed on the wood building element. Weathering stages may vary according to the part or element affected. To give wood the longest and best possible protection it is advisable to examine surfaces every year. Any damage found should be addressed immediately after cleaning.

        For cleaning and care, we recommend the care set for windows (2745) and doors (2746).

        We recommend that repairs be carried out using Aqua HSL-35 (7120) and Aqua DSL-55 (7220) or HSL-30 (7100) and LT Stain UV (2234)

        Observe current standards and guidelines for coating wood building elements outdoors (Codes of Practice issued by the German Association of Window and Facade Manufacturers (VFF), Code of Practice No. 18 issued by the German Federal Committee for Paint and the Protection of Material Assets (BFS), guidelines issued by the German Lacquer and Printing Ink Association (VdL) and ift guidelines issued by the Institut für Fenstertechnik).

    • Disposal instructions
      • Larger quantities of leftover product should be disposed of in the original containers in accordance with the applicable regulations. Completely empty, clean containers should be recycled. Do not dispose of together with household waste. Do not allow to enter the sewage system. Do not empty into drains.

    • Safety / regulations
      • For further information on the safety aspects of transporting, storing and handling the product and on disposal and environmental matters, please see the current Safety Data Sheet.