Article No. 347620

    Induline GW-306

    Water-based primer with protection against soft rot and blue stain

    Button remmers-mix Button VOC FR A+
    Colour: clear, lignin-stabilising | 3476
    Colour: clear, lignin-stabilising | 3476
    Please choose a colour
    Packaging unit

    Product specifications

    On delivery

    Binder Special resins
    Density (20°C) Approx. 1.015 - 1.13 g/cm³
    Odour Characteristic
    Preservative IPBC (3-iodo-2-propynyl butylcarbamate)
    Viscosity (20 °C) Runout time approx. 24 - 26 s in ISO cup 3 mm

    The stated values represent typical product characteristics and are not to be construed as binding product specifications.

    Field of application

    • For use outdoors
    • for dimensionally stable elements
    • for elements with limited dimensional stability
    • for not dimensionally stable elements
    • For professional users only
    • Wood outdoors which does not come into contact with the ground
    • Soft and hard woods
    • Dimensionally stable wood building elements: e.g. windows and doors
    • Wood building elements with limited dimensional stability, e.g. folding shutters, matchboarding, summerhouses
    • Wood building elements with no dimensional stability: e. g. fences, framework, carports, planking

    Properties

    • Water-based
    • Ready for use by dipping or flow-coating
    • Excellent flow characteristics on untreated wood
    • Good pore wetting performance
    • Outstanding (wet) adhesion
    • Protects against stain and blue rot
    • Preparation
      • Substrate requirements

        The substrate must be clean, dry, free of dust, grease and loose substances, and prepared in the correct manner.

        Dimensionally stable wood building elements: wood moisture content 11-15%

        Wood building elements with limited or no dimensional stability: wood moisture content max. 18%

    • Application
      • Automatic vacuum impregnation
      • Stir before use
      • Temperature of the material, air and substrate: from min. +15 °C to max. +30 °C
      • By brush / Dipping / Flow coating / Spraying only in closed facilities
      • Application requirements

        Temperature of the material, air and substrate: +15 °C to +30 °C. Processing conditions are between +15 °C and +30 °C at a relative humidity of 40 - 80%.

      • Stir well, including during application or after a break in work.

        Qualified specialist companies: brushing, dipping, flow-coating and spraying in closed systems only.

        Once dry, apply further coatings.

        Seal opened containers well and use contents as soon as possible.

    • Application instructions
      • Drying time: can be worked over after 4 h
      • Check colour, adhesion and compatibility with the substrate by setting up a trial area.

        Substances in oak may bleed, causing dark discolouration, when coated with water dilutable dispersion stains.

        Apply forced drying to tannin-containing woods.

        The best flow results on Accoya, oak and chestnut are achieved at a pH value of 9.0–9.5, corresponding to an additive content of 0.3–0.5% VP 20829 Additive (0366).

        If the viscosity increases due to evaporation, this must be compensated for using water (target viscosity: clear, special colours, lignin-stabilising: runout time approx. 23 - 27 s in ISO cup 3 mm; white: runout time approx. 34 - 45 s in ISO cup 3 mm)

        Dilute with up to 10% water to improve flow properties in unfavourable conditions (elevated temperatures, low humidity). Add water to make up for any moisture lost through evaporation.

        If foaming occurs in the flow coating system, it is recommended to add 0.2-1.0% VP 9325 defoaming agent - strength 2 (3231).

        The system finder on our website www.remmers.de contains coating recommendations for specific wood types to be used when treating windows and exterior doors.

        Observe the “Care and Maintenance of Dipping Tanks and Flow Coating Facilities” and “Notes on Operational Hygiene” information sheets.

      • Drying

        Can be overcoated: after approx. 4 hours (at 23 °C and 50% RH) If forced drying is used, can be overcoated: after approx. 90 minutes (20 minutes dripping/50 minutes drying phase (35 – 40 °C)/20 minutes cooling phase)

        Low temperatures, poor ventilation and high humidity delay drying.

      • Thinning

        Ready for use

    • Working tools / cleaning
      • Automatic vacuum impregnation
      • By brush / Dipping / Flow coating / Spraying only in closed facilities
      • Brush, dipping tank, flow coating facility, spray coating facility, vacuum machine

      • Clean tools with water or Aqua RK-898 Cleaning Concentrate immediately after use.

        Ensure that any residue from cleaning is disposed of correctly.

    • Storage / shelf life
      • Store frost-free and cool / protect for moisture / close containers
      • Store in well-sealed, original containers, out of the reach of children and in a dry, cool, well-ventilated room which is protected from direct sunlight and frost. No smoking is permitted in storage areas.

    • Usage
      • Approx. 120 ml - 140 ml / m² per layer applied
      • 120 - 140 ml/m² per coat

      • Depending on the processing method, wood type and wood surface.

    • Disposal instructions
      • European waste code 03 02 02* organochlorinated wood preservatives

        Larger quantities of leftover product should be disposed of in the original containers in accordance with the applicable regulations. Completely empty, clean containers should be recycled. Do not dispose of together with household waste. Do not allow to enter the sewage system. Do not empty into drains.

    • Safety / regulations
      • For further information on the safety aspects of transporting, storing and handling the product and on disposal and environmental matters, please see the current Safety Data Sheet.