Article No. 347820

    Induline GW-208

    Water-based, white primer with a film preservative

    Colour: white | 3478
    Packaging unit

    Product specifications

    On delivery

    Binder acrylate/alkyd resin
    Density (20°C) approx. 1.09 g/cm³
    Odour characteristic
    Preservative 3-Iodo-2-propynyl-butylcarbamate
    Viscosity (20 °C) flow time approx. 29-31 s in a 3 mm ISO cup

    The stated values represent typical product characteristics and are not to be construed as binding product specifications.

    Field of application

    • For use outdoors
    • for dimensionally stable elements
    • for elements with limited dimensional stability
    • for not dimensionally stable elements
    • For professional users only
    • For use on exterior wood
    • Soft and hard woods
    • Dimensionally stable wood building elements: e.g. windows and doors
    • Wood building elements with limited dimensional stability, e.g. folding shutters, matchboarding, summerhouses
    • Wood building elements with no dimensional stability: e. g. fences, framework, carports, planking

    Properties

    • Water-based
    • Ready for use by dipping or flow-coating
    • Less discolouration due to water-soluble substances in the wood
    • Good flow characteristics on untreated and impregnated wood
    • Good pore wetting performance
    • Outstanding (wet) adhesion
    • Film preservative protects against microbial damage
    • Preparation
      • Substrate requirements

        The substrate must be clean, dry, free of dust, grease and loose substances, and prepared in the correct manner.

        Dimensionally stable wood building elements: wood moisture content 11-15%

        Wood building elements with limited or no dimensional stability: wood moisture content max. 18%

      • Preparations

        If necessary, impregnate non-resistant woods with a wood preservative*.

        Observe BFS Code of Practice No. 18 "Coatings on Wood and Wooden Working Materials in Outdoor Areas".

    • Application
      • Stir before use
      • Temperature of the material, air and substrate: from min. +15 °C to max. +30 °C
      • By brush / Dipping / Flow coating / Spraying only in closed facilities
      • Application requirements

        Temperature of the material, air and substrate: from min. +15 °C to max. +30 °C.

      • Stir well, including during application or after a break in work.

        Qualified specialist companies: brushing, dipping, flow-coating and spraying in closed systems only.

        Once dry, apply an intermediate coat of this or another suitable product.

        Seal opened containers well and use contents as soon as possible.

    • Application instructions
      • Drying time: can be worked over after 4 h
      • Check colour, adhesion and compatibility with the substrate by setting up a trial area.

        The best flow results on Accoya, oak and chestnut are achieved at a pH value of 9.0–9.5, corresponding to an additive content of 0.3–0.5% VP 20829 Additive (0366).

        If viscosity increases due to evaporation, water must be used to make up for the lost moisture (target viscosity: flow time approx. 30–40 s in a 3 mm ISO cup).

        Dilute with up to 10% water to improve flow properties in unfavourable conditions (elevated temperatures, low humidity). Add water to make up for any moisture lost through evaporation.

        If foaming occurs in the flow coating facility, it is recommended to add 0.1–0.2% VP 21490 defoaming agent - strength 4 (0368).

        The product's sealing effect may be impaired if it is diluted too thinly, if the wood is too wet or if the recommended coating sequence, application volumes and drying times are not observed.

        With water based coating systems, there is always a residual risk that substances contained in the wood will cause discoloration.

        The system finder on our website www.remmers.de contains coating recommendations for specific wood types to be used when treating windows and exterior doors.

        Observe the “Care and Maintenance of Dipping Tanks and Flow Coating Facilities” and “Notes on Operational Hygiene” information sheets.

      • Drying

        Can be overcoated: after approx. 4 hours (at 23 °C and 50% RH) When forced drying is applied, can be overcoated: after approx. 90 mins (20 minutes dripping off time/50 minutes drying time (35–40 °C)/20 minutes cooling time)

        Low temperatures, poor ventilation and high humidity delay drying.

      • Thinning

        Ready to use. If neccessary with water (max. 10%)

    • Working tools / cleaning
      • By brush / Dipping / Flow coating/ Spraying tunnel
      • Acrylic brush, dipping tank, flow coating facilities, spray tunnel

      • Clean tools with water or Aqua RK-898 Cleaning Concentrate immediately after use.

    • Storage / shelf life
      • Shelf-life 12 months
      • Store frost-free and cool / protect for moisture / close containers
      • If stored unopened in its original container in a cool, dry place and protected against frost, the product will keep for at least 12 months.

    • Usage
      • Approx. 80 ml - 120 ml / m² per layer applied
      • 80-120 ml/m² per coat

    • Disposal instructions
      • Larger quantities of leftover product should be disposed of in the original containers in accordance with the applicable regulations. Completely empty, clean containers should be recycled. Do not dispose of together with household waste. Do not allow to enter the sewage system. Do not empty into drains.

    • Safety / regulations
      • For further information on the safety aspects of transporting, storing and handling the product and on disposal and environmental matters, please see the current Safety Data Sheet.

        Do not use on wood intended to come into direct contact with food or feed.