Article No. 542010

    All Primer

    Adhesive primer for metals, rigid PVC & wood that protects against rust and seals off substances in the wood

    Button VOC FR A
    Colour: white | 5420
    Colour: white | 5420
    Please choose a colour
    Packaging unit

    Product specifications

    On delivery

    Density (20°C) approx. 1.20 g/cm³
    Odour mild
    Viscosity thixotropic, approx. 1500-2000 mPa·s

    The stated values represent typical product characteristics and are not to be construed as binding product specifications.

    Field of application

    • For use indoors and outdoors
    • for dimensionally stable elements
    • for elements with limited dimensional stability
    • for not dimensionally stable elements
    • Primer and intermediate coat
    • Metal substrates, e.g. (galvanised) steel, pure aluminium, copper, brass
    • Rigid PVC
    • For use on interior and exterior wood

    Properties

    • Water-based
    • Very good adhesion to the substrate
    • Protects against corrosion
    • Water-based
    • Reduces yellow stains caused by water soluble substances in the wood when light shades of finishing coat are used
    • Low solvent, environmentally compatible, mild odour
    • Preparation
      • Substrate requirements

        Dimensionally stable wood building elements: wood moisture content 11-15%

        Wood building elements with limited or no dimensional stability: wood moisture content max. 18%

      • Preparations

        Thoroughly remove any dirt, grease and non-adhering old coatings.

         

        Wood substrates:

        Sand grey and weathered wood surfaces down to sound, bright wood.

        Remove loose and torn knots as well as resin that bleeds and clean with a suitable product (e.g. V 101 thinner, thinner & brush cleaner).

        Pre-treat wood in outdoor areas requiring protection against soft rot and blue stain with Remmers Wood Preservative Primer* (not necessary for wood in indoor areas).

        Observe BFS Code of Practice No. 18 "Coatings on Wood and Wooden Working Materials in Outdoor Areas".

        Iron, steel:

        Derust thoroughly. Remove scale layers and rolling skin (derust manually to SA 3 standard of cleanliness). The best results are achieved if the substrate has been sand blasted to SA 2.5 standard of cleanliness (DIN EN ISO 12944-4).

        Zinc (galvanised steel):

        Clean with an ammonium-based wetting agent, using an abrasive pad. Observe BFS Code of Practice No. 5.

        Aluminium:

        Clean with V 101 or V-890 thinner, or a cleaning agent that contains phosphoric acid. Observe BFS Code of Practice No. 6.

        Plastics:

        Treat rigid PVC, PUR, polyester, acrylic, and melamine resin coatings (Resopal) with V 101 or V-890 thinner and an abrasive pad.

    • Application
      • Stir before use
      • Temperature of the material, air and substrate: from min. +15 °C to max. +25 °C
      • By brush / By roller / Airless/airmix spraying
      • Application requirements

        Temperature of the material, air and substrate: from min. +15 °C to max. +25 °C.

      • Stir well.

        Apply with a brush, roller or by spraying.

        After drying and intermediate sanding, coat with a water-based or solvent-based lacquer.

        Observe the waiting times between coats.

    • Application instructions
      • Check colour, adhesion and compatibility with the substrate by setting up a trial area.

      • Drying

        Approx. 12 hours at 20 °C and 65% relative humidity.

        For faster drying, the coated object can be dried in a drying chamber up to a temperature of 60 °C.

        Low temperatures, poor ventilation and high humidity delay drying.

      • Thinning

        If necessary with water (up to 5%).

    • Working tools / cleaning
      • By brush / By roller / Airless/airmix spraying
      • Brush, roller, flow cup or airless spraying equipment

      • Clean tools immediately after use with water.

        Ensure that any residue from cleaning is disposed of correctly.

    • Storage / shelf life
      • Shelf-life 24 months
      • Store frost-free and cool / protect for moisture / close containers
      • If stored unopened in its original container in a cool, dry place and protected against frost, the product will keep for at least 24 months.

    • Usage
      • Approx. 100 ml / m² per layer applied
      • 100 ml/m² per coat 2 coats are necessary to provide protection against corrosion and to seal off substances contained in the wood.

    • General information
      • Check colour, adhesion and compatibility with the substrate by setting up a trial area.

    • Disposal instructions
      • Larger quantities of leftover product should be disposed of in the original containers in accordance with the applicable regulations. Completely empty, clean containers should be recycled. Do not dispose of together with household waste. Do not allow to enter the sewage system. Do not empty into drains.

    • Safety / regulations
      • For further information on the safety aspects of transporting, storing and handling the product and on disposal and environmental matters, please see the current Safety Data Sheet.

    Possible system products