Article No. 266620

    Induline T-778 Plus

    Water-based, translucent all-in-one coating system - fire behaviour tested to DIN EN 13501-1

    Colour: clear | 2666
    Colour: clear | 2666
    Please choose a colour
    Size / Quantity

    Product specifications

    Binder Acrylate/alkyd system
    Density (20°C) Approx. 1.045 g/cm³
    Odour Mild

    The stated values represent typical product characteristics and are not to be construed as binding product specifications.

    Field of application

    • For use on exterior wood
    • Wood that has been impregnated with Adolit BSS1: application tested in outdoor areas not directly exposed to weathering
    • Building elements with no or limited dimensional stability
    • Thermally treated wood
    • Only for industrial use as a system product with Adolit BSS 1

    Properties

    • Approved for system use with Adolit BSS1
    • Protects the wood against moisture and UV radiation
    • Does not flake
    • Does not tear
    • Film preserver protects against microbial damage
    • Preparation
      • Substrate requirements

        The substrate must be clean, dry, free of dust, grease and loose substances.

        Wood building elements with limited or no dimensional stability: wood moisture content max. 18%

      • Preparations

        Use a brush to remove excess salt residues.

    • Application
      • Stir well, including during application or after a break in work.

        Spray.

        Flow cup gun: nozzle size: 2.0 - 2.5 mm; atomiser air pressure: 2.0 - 3.0 bar.

        Airless spraying: nozzle size: 0.28-0.33 mm, material pressure: 80-100 bar (use yellow gun filter)

        Air-mix spraying: nozzle size: 0.28-0.33 mm; material pressure: 70-90 bar, atomiser air pressure 1-2 bar.

        After drying and, if necessary, intermediate sanding (P 280 - 320), apply a second coat.

        Seal opened containers well and use contents as soon as possible.

    • Application instructions
      • Check colour, adhesion and compatibility with the substrate by setting up a trial area.

        The treated components must be protected against rain and moisture (enclosed spaces, covered structures etc.) and must not be exposed to weathering.

        Light colours not suitable on thermally treated wood.

      • Drying

        Overcoating: after 1 - 2 hours

        Practice values at +20 °C and 65% relative humidity.

        Low temperatures, poor ventilation and high humidity delay drying.

      • Thinning

        Ready to use

    • Working tools / cleaning
      • Spraying equipment, board coating machine

      • Clean tools with water or Aqua RK-898 Cleaning Concentrate immediately after use.

        Ensure that any residue from cleaning is disposed of correctly.

    • Storage / shelf life
      • Store in well-sealed, original containers, out of the reach of children and in a dry, cool, well-ventilated room which is protected from direct sunlight and frost. No smoking is permitted in storage areas.

        If stored unopened in its original container in a cool, dry place and protected against frost, the product will keep for at least 12 months.

    • Usage
      • 93 ml/m² (100 g/m²) per coat in 2 coats (200 g/m²)

    • General information
      • Packing:

        When packing multiple wood components together, use an intermediate layer of foamed PE film or silicone-coated paper to separate them from one another. Do not pull the packing tape on the wood packets too tight.

        Care and maintenance:

        The coating system must always be kept in good condition. Any damage must be immediately reworked or repaired using this product.

         

        When coating technically modified woods and wood-based materials, the surface properties of the product may differ from those of natural woods. Before coating, a trial application and a suitability test must be carried out to check compatibility, adhesion, reaction to weathering and colour tone. Under certain circumstances, different maintenance intervals may apply. Please also take particular note of the specific instructions for surface treatment from the respective manufacturer. If you have any further questions, please contact Remmers Technical Service.

        Thermally modified woods are suspectible to colour changes due to weathering. This discolouration of the material can only be prevented to a limited degree through the use of high-quality stains.

    • Disposal instructions
      • Larger product residues must be disposed of in the original packaging in accordance with the applicable regulations.
        Do not pour liquid coating or residues down the drain, even when cleaning tools. Must not be disposed of with household waste. Completely empty packaging must be recycled.

    • Safety / regulations
      • For further information on the safety aspects of transporting, storing and handling the product and on disposal and environmental matters, please see the current Safety Data Sheet.