• 0000698011_Epoxy_OS_Color_New
  • 0021698202_Epoxy_OS_Color_New
    • 0000698011_Epoxy_OS_Color_New
    • 0021698202_Epoxy_OS_Color_New

    Article No. 698011

    Epoxy OS Color

    Pigmented coating

    Colour: special colours from 10 kg | 6980
    Colour: special colours from 10 kg | 6980
    Please choose a colour
    Packaging unit

    Product specifications

    On delivery

    Component A

    Density (20°C) 1.6 g/cm³
    Viscosity (25 °C) 3900 mPa s

    Component B

    Density (20°C) 1.1 g/cm³
    Viscosity (25 °C) 340 mPa s

    Mixture

    Density (20°C) 1.5 g/cm³
    Viscosity (25 °C) 1600 mPa s

    Once fully cured

    Once fully cured

    Shore D after 28 days > 78

    The stated values represent typical product characteristics and are not to be construed as binding product specifications.

    Field of application

    • Coating
    • Filled coating
    • Coating in DIBt-approved systems for common rooms (general building inspectorate approval Z-156.605-1594)

    Properties

    • Can be subjected to mechanical loads
    • Can be subjected to chemical loads
    • Suitable for hand pallet trucks and forklift trucks
    • Physiologically harmless once fully cured
    • Preparation
      • Substrate requirements

        The substrate must be firm, dimensionally stable, capable of bearing loads and free of loose constituents, dust, oil, grease, rubber marks and other substances that could interfere with adhesion.

        The adhesive pull strength of the surface after priming must be at least 1.5 N/mm² on average (smallest single value min. 1.0 N/mm²), compressive strength at least 25 N/mm².

        A suitable Remmers epoxy primer or epoxy scratch coat must always be used.

        Refer to the current Technical Data Sheet for detailed information on the single products.

        For works within the framework of the general building inspectorate approval, the substrates must correspond to the requirements of the approval and the system products mentioned therein must be used.

    • Preparation
      • Mixing ratio comp. A 82 : comp. B 18
      • Mixing time 3 min
      • Combination container

        Add the entire quantity of the hardener (component B) to the basic compound (component A).

        Mix thoroughly with a slow-speed electric mixer
        (approx. 300 - 400 rpm).

        Pour the mixture into a separate container and mix again thoroughly.

        Mix for at least 3 minutes.

        Insufficient mixing is indicated by streaks forming.

    • Application
      • Self-levelling coating / Apply standing
      • Pot life 25 min
      • Application temperature: min. 10 °C max. 30 °C
      • Application requirements

        Temperature of material, surroundings and substrate: min. +10 °C to max. +30 °C.

      • Temperature Foot traffic after
        +8 °C 48 hours
        +12 °C 30 hours
        +20 °C 16 hours

        Setting may be accelerated by adding ACC H. The associated directions for use are available upon request.

        As a general principle, higher temperatures will reduce and lower temperatures will increase the times stated.

    • Working tools / cleaning
      • Self-levelling coating / Apply standing
      • Toothed trowel, toothed spreader, spiked roller, suitable mixing equipment

      • More detailed information can be found in the Remmers Tool Programme.

        Clean tools, equipment and splashed material immediately while fresh with V 101 Thinner.

        Take suitable protective and waste disposal measures when cleaning.

    • Storage / shelf life
      • Store frost-free
      • Shelf-life 12 months
      • If stored unopened in the original container and kept cool, dry and protected from frost, min. 12 months (component A)/min. 24 months (component B).

    • Usage
      • See application examples

    • Application examples
      • Application
        Degree of filling with Selectmix 01/03
        Application rate binder [kg/m²]
        Application rate mixture [kg/m²]
        Possible toothed blade 
        Application rate per mm layer thickness [kg/m²]
        Coating
        < 1 mm
        unfilled
        0.8 - 1.0
        0.8 - 1.0
        No. 5
        --
        Coating approx. 1 mm
        unfilled
        1.3 - 1.5
        1.3 - 1.5
        No. 7
        1.50
        Filled coating
        1 : 0.3
        min. 1.3
        min. 1.8
        No. 25
        1.55
        Filled coating1 : 0.5
        min. 1.5
        min. 2.2
        No. 46
        1.65
        Filled coating1 : 0.7
        min. 1.8
        min. 3.1
        No. 55
        1.75

    • General information
      • Unless otherwise specified, all of the values and application rates given above have been determined under laboratory conditions (20 °C) using standard colours. Slight deviations from these values may arise if the product is worked with on site.

        H_B_183

        When coating continuous surfaces, only use materials with the same batch number as slight differences in colour, gloss and texture may occur.

        Application of the mixture by toothed trowel/toothed spreader. If the product is applied with a smoothing trowel/screed levelling tool, trowel marks may be visible on the finished surface.

        Special colours, low layer thickness or differing sand fractions as well as lower temperatures can reduce the maximum degree of filling of the material and possibly affect the visual appearance of the surface.

        In case of repairs on the surface or working up to existing surfaces, there will be a visible transition in appearance and texture.

        Abrasive mechanical loads leave traces of wear.

        Exposure to vehicles with metal or polyamide tyres as well as dynamic concentrated loads can cause faster wearing of the coating.

        Epoxy resins are generally not colourfast when exposed to UV light or weather.

        Further notes on working, system construction and maintenance of the listed products can be found in the latest Technical Data Sheets and the Remmers system recommendations.

    • Disposal instructions
      • Larger quantities of leftover product should be disposed of in the original containers in accordance with the applicable regulations. Completely empty, clean containers should be recycled. Do not dispose of together with household waste. Do not allow to enter the sewage system. Do not empty into drains.

    • Safety / regulations
      • For professional users only!

        For further information on the safety aspects of transporting, storing and handling the product and on disposal and environmental matters, please see the current Safety Data Sheet and the brochure entitled "Epoxy Resins in the Construction Industry and the Environment", issued by Deutsche Bauchemie e.V. (2nd edition 2009).

    Possible system products