Article No. 280620

    Multi Fill [basic]

    Filling compound and surface filler

    Colour: special colours | 2806
    Colour: special colours | 2806
    Please choose a colour
    Packaging unit

    Product specifications

    On delivery

    Flexural tensile strength (28 days) Approx. 3.5 N/mm²
    Compressive strength 24 h: approx. 3 N/mm²
    28 d: approx. 10 N/mm²
    Maximum grain size < 0.2 mm
    Bulk density Approx. 1.0 kg/dm³
    Water requirement 1.5-1.92 l/5 kg
    6.0-7.5 l/20 kg

    The stated values represent typical product characteristics and are not to be construed as binding product specifications.

    Field of application

    • For use indoors and outdoors
    • Indoors and outdoors
    • Filler for rendered surfaces, plane building blocks and finishing boards
    • Facades under water-repellent coatings


    • Fast setting
    • Water vapour permeable
    • Good adhesive properties
    • Can be feathered out to zero
    • Low-stress and crack-free setting
    • Can be sanded
    • Can be tinted with colour
    • Resistant to water, frost and weathering
    • Preparation
      • Substrate requirements

        Clean, dust-free and capable of supporting a load.

      • Preparations

        Pre-wet the substrate so that it is slightly moist.

    • Application
      • Mortar cover / Filling knife / Trowel application
      • Application temperature: min. 5 °C max. 25 °C
      • Application requirements

        Temperature of the material, air and substrate: from min. +5 °C to max. +25 °C

      • Apply product in the desired coating thickness.

        Smooth the surface using a suitable tool.

        Can be sanded once set.


    • Application instructions
      • Once it has hardened, mortar must not be made workable again by adding either water or more wet mortar.

        Protect wet mortar surfaces against frost, rain and drying out too quickly for at least 4 days.

        Hairline/shrinkage cracks are safe and are not cause for complaint as they do not impair the properties of the mortar.

        Do not use in permanently wet areas.

        Do not coat with silicate paints.

    • Working tools / cleaning
      • Mortar cover / Filling knife / Trowel application
      • Mixer, trowel, smoothing trowel

      • Clean tools with water while the material is still fresh.

    • Storage / shelf life
      • Protect form moisture
      • Shelf-life 12 months
      • If stored in an unopened container and in a dry place, the product will keep for approx. 12 months.

    • Usage
      • Approx. 1.0 kg / mm thick layer / m²
      • Approx. 1.0 kg/m²/mm layer thickness

      • Apply to a large enough trial area to determine the precise amount required.

    • General information
      • Do not work on substrates where moisture is penetrating from the rear.

        The colour that is obtained after drying and hardening depends on the ambient conditions and the processing method. For instance, a freshly smoothed surface will be lighter than one that is smoothed later or roughened. Different grain sizes of the same product may lead to slight differences in colour. Substrates soaked from the back may cause discolouration.

        Do not use on gypsum-based substrates.

        The mixing water must be of drinking water quality.

        Low chromate content in accordance with Directive 2003/53/EC.

        Always set up a trial area/trial areas first.

        Deviations from applicable regulations must be agreed separately.

        The relevant test certificates must be observed when planning and carrying out work.

    • Disposal instructions
      • Larger quantities of leftover product should be disposed of in the original containers in accordance with the applicable regulations. Completely empty, clean containers should be recycled. Do not dispose of together with household waste. Do not allow to enter the sewage system. Do not empty into drains.

    • Safety / regulations
      • For further information on the safety aspects of transporting, storing and handling the product and on disposal and environmental matters, please see the current Safety Data Sheet.