Article No. 058830

    RM GF

    Mineral stone substitution mortar, pourable

    Variant
    Variant
    Variant
    0588 | grey (inherent colour)
    Packaging unit

    Product specifications

    On delivery

    Flexural tensile strength (28 days) approx. 7 N/mm²
    Compressive strength (28 d) approx. 25 N/mm²
    E-modulus (DIN 1048) approx. 17 kN/mm²
    Maximum grain size 0.5 mm
    Bulk density Approx. 1.6 kg/dm³
    Water requirement 5.8 - 6.0 l/30 kg

    The stated values represent typical product characteristics and are not to be construed as binding product specifications.

    Field of application

    • For use indoors and outdoors
    • Moulding statues and sculptures using a casting process
    • Casting with open and closed moulds

    Properties

    • Pourable
    • Low free alkali content
    • Low inherent stress
    • UV-resistant pigments
    • Can be made hydrophobic
    • Preparation
      • Substrate requirements

        Clean, dust-free and capable of supporting a load.

      • Preparations

        Any necessary cleaning measures should be performed as gently as possible, e.g. by spraying with cold or hot water or steam cleaning; stubborn dirt should preferably be cleaned using the rotec soft blasting method or Remmers cleaning products (e.g. Facade Cleaner Paste, Clinker Cleaner AC, Combi WR).

        Preserve valuable heritage ornamental elements and statues by carefully removing encrusted dirt and using the appropriate Remmers Stone Strengthener to carry out repeated intensive strengthening.

        For further details on preparing substrates using stonemasonry techniques, see the separate document "Instructions for Use".

    • Application
      • Curtain coating
      • Application temperature: min. 5 °C max. 30 °C
      • Application requirements

        Temperature of the material, air and substrate: from min. 15 °C to max. +30 °C

      • Construct formwork if necessary.

        Slowly allow the mortar to flow along a suitable wooden batten or via a filling device into the mould in a thin, even layer.

        Re-compact if necessary.

        Depending on the size and shape of the copy created, it may be removed from the formwork and reworked if necessary after approx. 24 hours.

    • Application instructions
      • Once it has hardened, mortar must not be made workable again by adding either water or more wet mortar.

        The type and duration of the reworking and surface treatment will influence the colour.

        Slight deviations in colour between different batches are possible.

        Protect wet mortar surfaces against frost, rain and drying out too quickly for at least 4 days.

    • Working tools / cleaning
      • Curtain coating
      • Mixing tool, wide brush, trowel, spatula, foam rubber water sweeper, scraper

      • Clean tools with water while the material is still fresh.

    • Storage / shelf life
      • Protect form moisture
      • Shelf-life 12 months
      • If stored in an unopened container and in a dry place, the product will keep for approx. 12 months.

    • Usage
      • 1.8 kg / mm thick layer / m²
      • Approx. 1.8 kg/l cavity volume

      • Apply to a large enough trial area to determine the precise amount required.

    • General information
      • May contain traces of pyrite (iron sulphide).

        Do not use on gypsum-based substrates.

        Low chromate content in accordance with Directive 2003/53/EC.

        The characteristic data of the product were calculated under laboratory conditions at 20°C and 65% relative humidity.

        The mixing water must be of drinking water quality.

        Special colour according to colour number (MF no., colour swatches, NCS etc.) or submitted sample (in the case of changing or alternating colours, clearly mark the desired colour).

        The colour that is obtained after drying and hardening depends on the ambient conditions and the processing method. For instance, a freshly smoothed surface will be lighter than one that is smoothed later or roughened. Different grain sizes of the same product may lead to slight differences in colour. Substrates soaked from the back may cause discolouration.

        Always set up a trial area/trial areas first.

        Alkaline binders may cause a dissolution process on non-ferrous metals.

        Deviations from applicable regulations must be agreed separately.

        The relevant test certificates must be observed when planning and carrying out work.

    • Disposal instructions
      • Dispose of contents/container in accordance with local/regional/national/international regulations.

    • Safety / regulations
      • For further information on the safety aspects of transporting, storing and handling the product and on disposal and environmental matters, please see the current Safety Data Sheet.