• Epoxy UV 100 TX
  • Epoxy UV 100 TX
  • Epoxy UV 100 TX
  • Epoxy UV 100 TX
  • Epoxy UV 100 TX
    • Epoxy UV 100 TX
    • Epoxy UV 100 TX
    • Epoxy UV 100 TX
    • Epoxy UV 100 TX
    • Epoxy UV 100 TX

    Article No. 630004

    Epoxy UV 100 TX

    Thixotropic binder

    Variant
    6300 | Epoxy UV 100 TX
    Size / Quantity

    Product specifications

    Component A

    Density (20°C) 1.15 g/cm³
    Viscosity (25 °C) Thixotropic

    Component B

    Density (20°C) 1.02 g/cm³
    Viscosity (25 °C) 220 mPa s

    Mixture

    Density (20°C) 1.11 g/cm³
    Viscosity (25 °C) Thixotropic

    The stated values represent typical product characteristics and are not to be construed as binding product specifications.

    Field of application

    • Transparent adhesive and fixing layer for flake coatings
    • Pore closure for epoxy resin screeds

    Properties

    • Stable
    • Resistant to yellowing
    • Preparation
      • Substrate requirements

        The substrate must be firm, dimensionally stable, capable of bearing loads and free of loose constituents, dust, oil, grease, rubber marks and other substances that could interfere with adhesion.

        The substrate must be prepared using suitable Remmers products.

    • Preparation
      • Mixing ratio comp. A 74 : comp. B 26
      • Mixing time 3 min
      • Combination container

        Add the entire quantity of the hardener (component B) to the base compound (component A).

        Mix thoroughly with a slow-speed electric mixer
        (approx. 300 - 400 rpm).

        Pour the mixture into a separate container and mix again thoroughly.

        Mix for at least 3 minutes.

        Insufficient mixing is indicated by streaks forming.

    • Application
      • Application temperature: min. 12 °C max. 30 °C
      • By brush / By roller
      • Pot life 25 min
      • As a general principle, higher temperatures will reduce and lower temperatures will increase the times stated.

    • Working tools / cleaning
      • By brush / By roller
      • Smoothing trowel, rubber scraper, epoxy roller, mixer

      • More detailed information can be found in the Remmers Tool Programme.

        Clean tools, equipment and splashed material immediately while fresh with V 101.

        Take suitable protective and waste disposal measures when cleaning.

    • Storage / shelf life
      • Store frost-free
      • Shelf-life 12 months
      • If stored unopened in the original container and kept cool, dry and protected from frost, min. 12 months (component A)/min. 24 months (component B).

    • Usage
      • See application examples

    • Application examples
      • Pore filler

        Apply the mixed resin generously to the surface. Distribute with a suitable tool, e.g. rubber blade, and work into the substrate with an epoxy roller so that pores in the surface of the substrate are completely filled.

        It may be necessary to apply several layers.

        approx. 0.2 - 0.5 kg/m² binder

      • Fixation layer for flake coatings

        Apply the material to the surface and smooth over the flake tips using a plastic or metal trowel.

        Then use a textured or porous roller to level off the material by rolling crosswise.

        approx. 0.3 kg/m² binder

    • General information
      • Unless otherwise specified, all of the values and application rates given above have been determined under laboratory conditions (20 °C) using standard colours. Slight deviations from these values may arise if the product is worked with on site.

        Abrasive mechanical loads leave traces of wear.

        Suitable for vehicle traffic with rubber tyres; not suitable for vehicle loads with metal or polyamide tyres nor for dynamic point loads.

        Epoxy resins are generally not colourfast when exposed to UV light or weather.

        When coating continuous surfaces, only use materials with the same batch number as slight differences in colour, gloss and texture may occur.

        When using to fix flake coatings, an additional seal coat is necessary.

        Further notes on working, system construction and maintenance of the listed products can be found in the latest Technical Data Sheets and the Remmers system recommendations.

    • Disposal instructions
      • Larger quantities of leftover product should be disposed of in the original containers in accordance with the applicable regulations. Completely empty, clean containers should be recycled. Do not dispose of together with household waste. Do not allow to enter the sewage system. Do not empty into drains.

    • Safety / regulations
      • For professional users only!

        For further information on the safety aspects of transporting, storing and handling the product and on disposal and environmental matters, please see the current Safety Data Sheet and the brochure entitled "Epoxy Resins in the Construction Industry and the Environment", issued by Deutsche Bauchemie e.V. (3rd edition 2022).