• Induline LW-717 Grey Protect

    Article No. 164120

    Induline LW-717 Grey Protect

    Water-based pre-greying stain for exterior wood

    Colour: special colours | 1641
    Colour: special colours | 1641
    Please choose a colour
    Size / Quantity

    Brochures and Catalogues

    product.brochures.loading

    Product specifications

    Density (20°C) Approx. 1.03 g/cm³
    Odour Characteristic
    Runout time s (20° C, DIN 4) Approx. 18 at 20 °C

    The stated values represent typical product characteristics and are not to be construed as binding product specifications.

    Field of application

    • For use outdoors
    • for elements with limited dimensional stability
    • for not dimensionally stable elements
    • For professional users only
    • For use on exterior wood
    • Softwoods
    • Wood building elements with limited dimensional stability: e.g. matchboarding, facade elements
    • Wood building elements with no dimensional stability: e.g. fences, framework, carports, planking

    Properties

    • Water-based
    • Natural grey tones for exterior wood
    • Especially natural appearance on textured wood
    • Maintenance-free: uniform transition from pre-greying to natural greying due to weathering
    • Evens out colour differences in areas with different levels of exposure to weathering
    • Water-based: does not give off any unpleasant odours and tools can be cleaned with water
    • Outstanding (wet) adhesion
    • Good block resistance
    • Breathable
    • Film preserver protects against microbial damage
    • Preparation
      • Substrate requirements

        The substrate must be clean, dry, free of dust, grease and loose substances, and prepared in the correct manner.

        Wood building elements with limited or no dimensional stability: wood moisture content max. 18%

      • Preparations

        If necessary, impregnate non-resistant woods with a wood preservative* (*Use biocides safely. Always read the label and product information before use).

        Remove resin galls.

    • Application
      • Application temperature: min. 10 °C max. 30 °C
      • Stir before use
      • Stir well, including during application or after a break in work.

        Apply by brushing or spraying.

        Industrial series production (VACUMAT®, board coating machine)

        Seal opened containers well and use contents as soon as possible.

    • Application instructions
      • Drying time: can be worked over after 12 h
      • Check colour, adhesion and compatibility with the substrate by setting up a trial area.

        Before coating technically modified woods and wood-based materials, apply the product to a trial surface and conduct a suitability test on the desired area of use.

        Wood types with a high resin content can cause damage to the coating.

      • Drying

        Coated pieces can be stacked after 12 hours of drying.
        (Practice values at 20 °C and 65% relative humidity)

        If forced drying is used, coated pieces can be stacked after approx. 20 minutes depending on the system used / the workpiece must be cooled to < 25 °C prior to packing.

        Low temperatures, poor ventilation and high humidity delay drying.

      • Thinning

        Ready to use

    • Working tools / cleaning
      • Flat brush, airless/airmix spraying equipment, VACUMAT® vacuum equipment, board coating machine

        Clean tools with water or Aqua RK-898 Cleaning Concentrate immediately after use.

        Ensure that any residue from cleaning is disposed of correctly.

    • Storage / shelf life
      • Store frost-free and cool / protect for moisture / close containers
      • Shelf-life 12 months
      • If stored unopened in its original container in a cool, dry place and protected against frost, the product will keep for at least 12 months.

    • Usage
      • Approx. 80 ml - 120 ml / m² per layer applied
      • 80 - 120 ml/m² in one coat

    • General information
      • Because the product is primarily designed for industrial series production (VACUMAT®), colour variations may occur when applying the material manually. A trial area should be set up to test the colour on the substrate using your chosen application method. For further information, please contact the Remmers Technical Service.

    • Disposal instructions
      • Larger quantities of leftover product should be disposed of in the original containers in accordance with the applicable regulations. Completely empty, clean containers should be recycled. Do not dispose of together with household waste. Do not allow to enter the sewage system. Do not empty into drains.

    • Safety / regulations
      • For further information on the safety aspects of transporting, storing and handling the product and on disposal and environmental matters, please see the current Safety Data Sheet.